NVIDIA Accelerated Linux Graphics Driver README and Installation Guide NVIDIA Corporation Last Updated: Thu May 27 17:56:26 PDT 2010 Most Recent Driver Version: 256.29 Published by NVIDIA Corporation 2701 San Tomas Expressway Santa Clara, CA 95050 NOTICE: ALL NVIDIA DESIGN SPECIFICATIONS, REFERENCE BOARDS, FILES, DRAWINGS, DIAGNOSTICS, LISTS, AND OTHER DOCUMENTS (TOGETHER AND SEPARATELY, "MATERIALS") ARE BEING PROVIDED "AS IS." NVIDIA MAKES NO WARRANTIES, EXPRESSED, IMPLIED, STATUTORY, OR OTHERWISE WITH RESPECT TO THE MATERIALS, AND EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE. Information furnished is believed to be accurate and reliable. However, NVIDIA Corporation assumes no responsibility for the consequences of use of such information or for any infringement of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of NVIDIA Corporation. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. NVIDIA Corporation products are not authorized for use as critical components in life support devices or systems without express written approval of NVIDIA Corporation. NVIDIA, the NVIDIA logo, NVIDIA nForce, GeForce, NVIDIA Quadro, Vanta, TNT2, TNT, RIVA, RIVA TNT, Quincunx Antialiasing, and TwinView are registered trademarks or trademarks of NVIDIA Corporation in the United States and/or other countries. Linux is a registered trademark of Linus Torvalds. Fedora and Red Hat are trademarks of Red Hat, Inc. SuSE is a registered trademark of SuSE AG. Mandriva is a registered trademark of Mandriva S.A. Intel and Pentium are registered trademarks of Intel Corporation. Athlon is a registered trademark of Advanced Micro Devices. OpenGL is a registered trademark of Silicon Graphics Inc. PCI Express is a registered trademark and/or service mark of PCI-SIG. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Other company and product names may be trademarks or registered trademarks of the respective owners with which they are associated. Copyright 2006 - 2010 NVIDIA Corporation. All rights reserved. ______________________________________________________________________________ TABLE OF CONTENTS ______________________________________________________________________________ Chapter 1. Introduction Chapter 2. Minimum Software Requirements Chapter 3. Selecting and Downloading the NVIDIA Packages for Your System Chapter 4. Installing the NVIDIA Driver Chapter 5. Listing of Installed Components Chapter 6. Configuring X for the NVIDIA Driver Chapter 7. Frequently Asked Questions Chapter 8. Common Problems Chapter 9. Known Issues Chapter 10. Allocating DMA Buffers on 64-bit Platforms Chapter 11. Specifying OpenGL Environment Variable Settings Chapter 12. Configuring AGP Chapter 13. Configuring TwinView Chapter 14. Configuring GLX in Xinerama Chapter 15. Configuring Multiple X Screens on One Card Chapter 16. Configuring TV-Out Chapter 17. Using the XRandR Extension Chapter 18. Configuring a Notebook Chapter 19. Programming Modes Chapter 20. Configuring Flipping and UBB Chapter 21. Using the Proc Filesystem Interface Chapter 22. Configuring Power Management Support Chapter 23. Using the X Composite Extension Chapter 24. Using the nvidia-settings Utility Chapter 25. Configuring SLI and Multi-GPU FrameRendering Chapter 26. Configuring Frame Lock and Genlock Chapter 27. Configuring SDI Video Output Chapter 28. Configuring Depth 30 Displays Chapter 29. NVIDIA Contact Info and Additional Resources Chapter 30. Acknowledgements Appendix A. Supported NVIDIA GPU Products Appendix B. X Config Options Appendix C. Display Device Names Appendix D. GLX Support Appendix E. Dots Per Inch Appendix F. i2c Bus Support Appendix G. XvMC Support Appendix H. VDPAU Support Appendix I. Tips for New Linux Users ______________________________________________________________________________ Chapter 1. Introduction ______________________________________________________________________________ 1A. ABOUT THE NVIDIA ACCELERATED LINUX GRAPHICS DRIVER The NVIDIA Accelerated Linux Graphics Driver brings accelerated 2D functionality and high-performance OpenGL support to Linux x86 with the use of NVIDIA graphics processing units (GPUs). These drivers provide optimized hardware acceleration for OpenGL and X applications and support nearly all recent NVIDIA GPU products (see Appendix A for a complete list of supported GPUs). TwinView, TV-Out and flat panel displays are also supported. 1B. ABOUT THIS DOCUMENT This document provides instructions for the installation and use of the NVIDIA Accelerated Linux Graphics Driver. Chapter 3, Chapter 4 and Chapter 6 walk the user through the process of downloading, installing and configuring the driver. Chapter 7 addresses frequently asked questions about the installation process, and Chapter 8 provides solutions to common problems. The remaining chapters include details on different features of the NVIDIA Linux Driver. Frequently asked questions about specific tasks are included in the relevant chapters. These pages are posted on NVIDIA's web site (http://www.nvidia.com), and are installed in '/usr/share/doc/NVIDIA_GLX-1.0/'. 1C. ABOUT THE AUDIENCE It is assumed that the user and reader of this document has at least a basic understanding of Linux techniques and terminology. However, new Linux users can refer to Appendix I for details on parts of the installation process. 1D. ADDITIONAL INFORMATION In case additional information is required, Chapter 29 provides contact information for NVIDIA Linux driver resources, as well as a brief listing of external resources. ______________________________________________________________________________ Chapter 2. Minimum Software Requirements ______________________________________________________________________________ Software Element Min Requirement Check With... --------------------- --------------------- --------------------- Linux kernel 2.4.7 `cat /proc/version` XFree86/X.Org 4.0.1/6.7 `XFree86 -version/Xorg -version` Kernel modutils 2.1.121 `insmod --version` If you need to build the NVIDIA kernel module: Software Element Min Requirement Check With... --------------------- --------------------- --------------------- binutils 2.9.5 `size --version` GNU make 3.77 `make --version` gcc 2.91.66 `gcc --version` glibc 2.0 `ls /lib/libc.so.*` > 6 All official stable kernel releases from 2.4.7 and up are supported; "prerelease" versions such as "2.6.23-rc1" are not supported, nor are development series kernels such as 2.3.x or 2.5.x. The Linux kernel can be downloaded from http://www.kernel.org or one of its mirrors. binutils and gcc can be retrieved from http://www.gnu.org or one of its mirrors. If you are using XFree86, but do not have a file '/var/log/XFree86.0.log', then you probably have a 3.x version of XFree86 and must upgrade. If you are setting up the X Window System for the first time, it is often easier to begin with one of the open source drivers that ships with XFree86 and X.Org (either "nv", "vga" or "vesa"). Once your system is operating properly with the open source driver, you may then switch to the NVIDIA driver. Note that newer NVIDIA GPUs may not work with older versions of the "nv" driver shipped with X.Org and XFree86. For example, the "nv" driver that shipped with X.Org's X11R7.2 release did not recognize the GeForce 8 family and the Quadro 4600/5600 GPUs. This was fixed in the X11R7.3 release. X.Org releases (and individual packages) can be retrieved from http://www.x.org/. These software packages may also be available through your Linux distributor. ______________________________________________________________________________ Chapter 3. Selecting and Downloading the NVIDIA Packages for Your System ______________________________________________________________________________ NVIDIA drivers can be downloaded from the NVIDIA website (http://www.nvidia.com). The NVIDIA graphics driver uses a Unified Driver Architecture: the single graphics driver supports all modern NVIDIA GPUs. "Legacy" GPU support has been moved from the unified driver to special legacy GPU driver releases. See Appendix A for a list of legacy GPUs. The NVIDIA graphics driver is bundled in a self-extracting package named 'NVIDIA-Linux-x86-256.29.run'. On Linux-x86_64, that file contains both the 64-bit driver binaries as well as 32-bit compatibility driver binaries; the 'NVIDIA-Linux-x86-256.29-no-compat32.run' file only contains the 64-bit driver binaries. ______________________________________________________________________________ Chapter 4. Installing the NVIDIA Driver ______________________________________________________________________________ This chapter provides instructions for installing the NVIDIA driver. Note that after installation, but prior to using the driver, you must complete the steps described in Chapter 6. Additional details that may be helpful for the new Linux user are provided in Appendix I. 4A. BEFORE YOU BEGIN Before you begin the installation, exit the X server and terminate all OpenGL applications (note that it is possible that some OpenGL applications persist even after the X server has stopped). You should also set the default run level on your system such that it will boot to a VGA console, and not directly to X. Doing so will make it easier to recover if there is a problem during the installation process. See Appendix I for details. 4B. STARTING THE INSTALLER After you have downloaded the file 'NVIDIA-Linux-x86-256.29.run', change to the directory containing the downloaded file, and as the 'root' user run the executable: # cd yourdirectory # sh NVIDIA-Linux-x86-256.29.run The '.run' file is a self-extracting archive. When executed, it extracts the contents of the archive and runs the contained 'nvidia-installer' utility, which provides an interactive interface to walk you through the installation. 'nvidia-installer' will also install itself to '/usr/bin/nvidia-installer', which may be used at some later time to uninstall drivers, auto-download updated drivers, etc. The use of this utility is detailed later in this chapter. You may also supply command line options to the '.run' file. Some of the more common options are listed below. Common '.run' Options --info Print embedded info about the '.run' file and exit. --check Check integrity of the archive and exit. --extract-only Extract the contents of './NVIDIA-Linux-x86-256.29.run', but do not run 'nvidia-installer'. --help Print usage information for the common commandline options and exit. --advanced-options Print usage information for common command line options as well as the advanced options, and then exit. 4C. INSTALLING THE KERNEL INTERFACE The NVIDIA kernel module has a kernel interface layer that must be compiled specifically for each kernel. NVIDIA distributes the source code to this kernel interface layer. When the installer is run, it will check your system for the required kernel sources and compile the kernel interface. You must have the source code for your kernel installed for compilation to work. On most systems, this means that you will need to locate and install the correct kernel-source, kernel-headers, or kernel-devel package; on some distributions, no additional packages are required. After the correct kernel interface has been compiled, the kernel interface will be linked with the closed-source portion of the NVIDIA kernel module. This requires that you have a linker installed on your system. The linker, usually '/usr/bin/ld', is part of the binutils package. You must have a linker installed prior to installing the NVIDIA driver. 4D. FEATURES OF THE INSTALLER Without options, the '.run' file executes the installer after unpacking it. The installer can be run as a separate step in the process, or can be run at a later time to get updates, etc. Some of the more important commandline options of 'nvidia-installer' are: 'nvidia-installer' options --uninstall During installation, the installer will make backups of any conflicting files and record the installation of new files. The uninstall option undoes an install, restoring the system to its pre-install state. --latest Connect to NVIDIA's FTP site, and report the latest driver version and the url to the latest driver file. --update Connect to NVIDIA's FTP site, download the most recent driver file, and install it. --ui=none The installer uses an ncurses-based user interface if it is able to locate the correct ncurses library. Otherwise, it will fall back to a simple commandline user interface. This option disables the use of the ncurses library. ______________________________________________________________________________ Chapter 5. Listing of Installed Components ______________________________________________________________________________ The NVIDIA Accelerated Linux Graphics Driver consists of the following components (filenames in parenthesis are the full names of the components after installation; "x.y.z" denotes the current version. In these cases appropriate symlinks are created during installation): o An X driver (/usr/X11R6/lib/modules/drivers/nvidia_drv.so); this driver is needed by the X server to use your NVIDIA hardware. o A GLX extension module for X (/usr/X11R6/lib/modules/extensions/libglx.so.x.y.z); this module is used by the X server to provide server-side GLX support. o An X module for wrapped software rendering (/usr/X11R6/lib/modules/libnvidia-wfb.so.x.y.z and optionally, /usr/X11R6/lib/modules/libwfb.so); this module is used by the X driver to perform software rendering on GeForce 8 series GPUs. If libwfb.so already exists, nvidia-installer will not overwrite it. Otherwise, it will create a symbolic link from libwfb.so to libnvidia-wfb.so.x.y.z. o An OpenGL library (/usr/lib/libGL.so.x.y.z); this library provides the API entry points for all OpenGL and GLX function calls. It is linked to at run-time by OpenGL applications. o An OpenGL core library (/usr/lib/libnvidia-glcore.so.x.y.z); this library is implicitly used by libGL and by libglx. It contains the core accelerated 3D functionality. You should not explicitly load it in your X config file -- that is taken care of by libglx. o Two XvMC (X-Video Motion Compensation) libraries: a static library and a shared library (/usr/X11R6/lib/libXvMCNVIDIA.a, /usr/X11R6/lib/libXvMCNVIDIA.so.x.y.z); see Appendix G for details. o Three VDPAU (Video Decode and Presentation API for Unix-like systems) libraries: The top-level wrapper (/usr/X11R6/lib/libvdpau.so.x.y.z), a debug trace library (/usr/X11R6/lib/libvdpau_trace.so.x.y.z), and the NVIDIA implementation (/usr/X11R6/lib/libvdpau_nvidia.so.x.y.z). See Appendix H for details. o Two CUDA libraries (/usr/lib/libcuda.so.x.y.z, /usr/lib/libcuda.la); these libraries provide runtime support for CUDA (high-performance computing on the GPU) applications. o A kernel module (/lib/modules/`uname -r`/video/nvidia.o or /lib/modules/`uname -r`/kernel/drivers/video/nvidia.o); this kernel module provides low-level access to your NVIDIA hardware for all of the above components. It is generally loaded into the kernel when the X server is started, and is used by the X driver and OpenGL. nvidia.o consists of two pieces: the binary-only core, and a kernel interface that must be compiled specifically for your kernel version. Note that the Linux kernel does not have a consistent binary interface like the X server, so it is important that this kernel interface be matched with the version of the kernel that you are using. This can either be accomplished by compiling yourself, or using precompiled binaries provided for the kernels shipped with some of the more common Linux distributions. o OpenGL and GLX header files (/usr/include/GL/gl.h, /usr/include/GL/glext.h, /usr/include/GL/glx.h, and /usr/include/GL/glxext.h); these are also installed in /usr/share/doc/NVIDIA_GLX-1.0/include/GL/. You can request that these files not be included in /usr/include/GL/ by passing the "--no-opengl-headers" option to the .run file during installation. o CUDA header files (/usr/include/cuda/cuda.h, /usr/include/cuda/cudaGL.h); these files are necessary for building CUDA applications. o The nvidia-tls libraries (/usr/lib/libnvidia-tls.so.x.y.z and /usr/lib/tls/libnvidia-tls.so.x.y.z); these files provide thread local storage support for the NVIDIA OpenGL libraries (libGL, libnvidia-glcore, and libglx). Each nvidia-tls library provides support for a particular thread local storage model (such as ELF TLS), and the one appropriate for your system will be loaded at run time. o The application nvidia-installer (/usr/bin/nvidia-installer) is NVIDIA's tool for installing and updating NVIDIA drivers. See Chapter 4 for a more thorough description. o The application nvidia-xconfig (/usr/bin/nvidia-xconfig) is NVIDIA's tool for manipulating X server configuration files. See Chapter 6 for more information. o The application nvidia-settings (/usr/bin/nvidia-settings) is NVIDIA's tool for dynamic configuration while the X server is running. See Chapter 24 for more information. Problems will arise if applications use the wrong version of a library. This can be the case if there are either old libGL libraries or stale symlinks left lying around. If you think there may be something awry in your installation, check that the following files are in place (these are all the files of the NVIDIA Accelerated Linux Graphics Driver, as well as their symlinks): /usr/lib/xorg/modules/drivers/nvidia_drv.so /usr/lib/xorg/modules/libwfb.so (if your X server is new enough), or /usr/lib/xorg/modules/libnvidia-wfb.so and /usr/lib/xorg/modules/libwfb.so -> libnvidia-wfb.so /usr/lib/xorg/modules/extensions/libglx.so.x.y.z /usr/lib/xorg/modules/extensions/libglx.so -> libglx.so.x.y.z (the above may also be in /usr/lib/modules or /usr/X11R6/lib/modules) /usr/lib/libGL.so.x.y.z /usr/lib/libGL.so.x -> libGL.so.x.y.z /usr/lib/libGL.so -> libGL.so.x /usr/lib/libnvidia-glcore.so.x.y.z /usr/lib/libcuda.so.x.y.z /usr/lib/libcuda.so -> libcuda.so.x.y.z /lib/modules/`uname -r`/video/nvidia.{o,ko}, or /lib/modules/`uname -r`/kernel/drivers/video/nvidia.{o,ko} If there are other libraries whose "soname" conflicts with that of the NVIDIA libraries, ldconfig may create the wrong symlinks. It is recommended that you manually remove or rename conflicting libraries (be sure to rename clashing libraries to something that ldconfig will not look at -- we have found that prepending "XXX" to a library name generally does the trick), rerun 'ldconfig', and check that the correct symlinks were made. An example of a library that often creates conflicts is "/usr/X11R6/lib/libGL.so*". If the libraries appear to be correct, then verify that the application is using the correct libraries. For example, to check that the application /usr/X11R6/bin/glxgears is using the NVIDIA libraries, run: % ldd /usr/X11R6/bin/glxgears linux-gate.so.1 => (0xffffe000) libGL.so.1 => /usr/lib/libGL.so.1 (0xb7ed1000) libXext.so.6 => /usr/X11R6/lib/libXext.so.6 (0xb7ec0000) libX11.so.6 => /usr/X11R6/lib/libX11.so.6 (0xb7de0000) libpthread.so.0 => /lib/tls/libpthread.so.0 (0x00946000) libm.so.6 => /lib/tls/libm.so.6 (0x0075d000) libc.so.6 => /lib/tls/libc.so.6 (0x00631000) libnvidia-tls.so.256.29 => /usr/lib/tls/libnvidia-tls.so.__DRV_VER__ (0xb7ddd000) libnvidia-glcore.so.256.29 => /usr/lib/libnvidia-glcore.so.__DRV_VER__ (0xb5d1f000) libdl.so.2 => /lib/libdl.so.2 (0x00782000) /lib/ld-linux.so.2 (0x00614000) Check the files being used for libGL -- if it is something other than the NVIDIA library, then you will need to either remove the library that is getting in the way or adjust your ld search path using the 'LD_LIBRARY_PATH' environment variable. You may want to consult the man pages for 'ldconfig' and 'ldd'. ______________________________________________________________________________ Chapter 6. Configuring X for the NVIDIA Driver ______________________________________________________________________________ The X configuration file provides a means to configure the X server. This section describes the settings necessary to enable the NVIDIA driver. A comprehensive list of parameters is provided in Appendix B. The NVIDIA Driver includes a utility called nvidia-xconfig, which is designed to make editing the X configuration file easy. You can also edit it by hand. 6A. USING NVIDIA-XCONFIG TO CONFIGURE THE X SERVER nvidia-xconfig will find the X configuration file and modify it to use the NVIDIA X driver. In most cases, you can simply answer "Yes" when the installer asks if it should run it. If you need to reconfigure your X server later, you can run nvidia-xconfig again from a terminal. nvidia-xconfig will make a backup copy of your configuration file before modifying it. Note that the X server must be restarted for any changes to its configuration file to take effect. More information about nvidia-xconfig can be found in the nvidia-xconfig manual page by running. % man nvidia-xconfig 6B. MANUALLY EDITING THE CONFIGURATION FILE In April 2004 the X.Org Foundation released an X server based on the XFree86 server. While your release may use the X.Org X server, rather than XFree86, the differences between the two should have no impact on NVIDIA Linux users with two exceptions: o The X.Org configuration file is '/etc/X11/xorg.conf' while the XFree86 configuration file is '/etc/X11/XF86Config'. The files use the same syntax. This document refers to both files as "the X config file". o The X.Org log file is '/var/log/Xorg.#.log' while the XFree86 log file is '/var/log/XFree86.#.log' (where '#' is the server number -- usually 0). The format of the log files is nearly identical. This document refers to both files as "the X log file". In order for any changes to be read into the X server, you must edit the file used by the server. While it is not unreasonable to simply edit both files, it is easy to determine the correct file by searching for the line (==) Using config file: in the X log file. This line indicates the name of the X config file in use. If you do not have a working X config file, there are a few different ways to obtain one. A sample config file is included both with the XFree86 distribution and with the NVIDIA driver package (at '/usr/share/doc/NVIDIA_GLX-1.0/'). The 'nvidia-xconfig' utility, provided with the NVIDIA driver package, can generate a new X configuration file. Additional information on the X config syntax can be found in the XF86Config manual page (`man XF86Config` or `man xorg.conf`). If you have a working X config file for a different driver (such as the "nv" or "vesa" driver), then simply edit the file as follows. Remove the line: Driver "nv" (or Driver "vesa") (or Driver "fbdev") and replace it with the line: Driver "nvidia" Remove the following lines: Load "dri" Load "GLCore" In the "Module" section of the file, add the line (if it does not already exist): Load "glx" If the X config file does not have a "Module" section, you can safely skip the last step if the X server installed on your system is an X.Org X server or an XFree86 X release version 4.4.0 or greater. If you are using an older XFree86 X server, add the following to your X config file: Section "Module" Load "extmod" Load "dbe" Load "type1" Load "freetype" Load "glx" EndSection There are numerous options that may be added to the X config file to tune the NVIDIA X driver. See Appendix B for a complete list of these options. Once you have completed these edits to the X config file, you may restart X and begin using the accelerated OpenGL libraries. After restarting X, any OpenGL application should automatically use the new NVIDIA libraries. (NOTE: If you encounter any problems, see Chapter 8 for common problem diagnoses.) ______________________________________________________________________________ Chapter 7. Frequently Asked Questions ______________________________________________________________________________ This section provides answers to frequently asked questions associated with the NVIDIA Linux x86 Driver and its installation. Common problem diagnoses can be found in Chapter 8 and tips for new users can be found in Appendix I. Also, detailed information for specific setups is provided in the Appendices. NVIDIA-INSTALLER Q. How do I extract the contents of the '.run' without actually installing the driver? A. Run the installer as follows: # sh NVIDIA-Linux-x86-256.29.run --extract-only This will create the directory NVIDIA-Linux-x86-256.29, containing the uncompressed contents of the '.run' file. Q. How can I see the source code to the kernel interface layer? A. The source files to the kernel interface layer are in the kernel directory of the extracted .run file. To get to these sources, run: # sh NVIDIA-Linux-x86-256.29.run --extract-only # cd NVIDIA-Linux-x86-256.29/kernel/ Q. How and when are the the NVIDIA device files created? A. Depending on the target system's configuration, the NVIDIA device files used to be created in one of three different ways: o at installation time, using mknod o at module load time, via devfs (Linux device file system) o at module load time, via hotplug/udev With current NVIDIA driver releases, device files are created or modified by the X driver when the X server is started. By default, the NVIDIA driver will attempt to create device files with the following attributes: UID: 0 - 'root' GID: 0 - 'root' Mode: 0666 - 'rw-rw-rw-' Existing device files are changed if their attributes don't match these defaults. If you want the NVIDIA driver to create the device files with different attributes, you can specify them with the "NVreg_DeviceFileUID" (user), "NVreg_DeviceFileGID" (group) and "NVreg_DeviceFileMode" NVIDIA Linux kernel module parameters. For example, the NVIDIA driver can be instructed to create device files with UID=0 (root), GID=44 (video) and Mode=0660 by passing the following module parameters to the NVIDIA Linux kernel module: NVreg_DeviceFileUID=0 NVreg_DeviceFileGID=44 NVreg_DeviceFileMode=0660 The "NVreg_ModifyDeviceFiles" NVIDIA kernel module parameter will disable dynamic device file management, if set to 0. Q. Why does NVIDIA not provide RPMs? A. Not every Linux distribution uses RPM, and NVIDIA provides a single solution that works across all Linux distributions. NVIDIA encourages Linux distributions to repackage and redistribute the NVIDIA Linux driver in their native package management formats. These repackaged NVIDIA drivers are likely to inter-operate best with the Linux distribution's package management technology. For this reason, NVIDIA encourages users to use their distribution's repackaged NVIDIA driver, where available. Q. Can the nvidia-installer use a proxy server? A. Yes, because the FTP support in nvidia-installer is based on snarf, it will honor the 'FTP_PROXY', 'SNARF_PROXY', and 'PROXY' environment variables. Q. What is the significance of the '-no-compat32' suffix on Linux-x86_64 '.run' files? A. To distinguish between Linux-x86_64 driver package files that do or do not also contain 32-bit compatibility libraries, "-no-compat32" is be appended to the latter. 'NVIDIA-Linux-x86-256.29.run' contains both 64-bit and 32-bit driver binaries; but 'NVIDIA-Linux-x86-256.29-no-compat32.run' omits the 32-bit compatibility libraries. Q. Can I add my own precompiled kernel interfaces to a '.run' file? A. Yes, the --add-this-kernel '.run' file option will unpack the '.run' file, build a precompiled kernel interface for the currently running kernel, and repackage the '.run' file, appending '-custom' to the filename. This may be useful, for example. if you administer multiple Linux computers, each running the same kernel. Q. Where can I find the source code for the 'nvidia-installer' utility? A. The 'nvidia-installer' utility is released under the GPL. The source code for the version of nvidia-installer built with driver 256.29 is in 'nvidia-installer-256.29.tar.bz2' available here: ftp://download.nvidia.com/XFree86/nvidia-installer/ NVIDIA DRIVER Q. Where should I start when diagnosing display problems? A. One of the most useful tools for diagnosing problems is the X log file in '/var/log'. Lines that begin with "(II)" are information, "(WW)" are warnings, and "(EE)" are errors. You should make sure that the correct config file (i.e. the config file you are editing) is being used; look for the line that begins with: (==) Using config file: Also make sure that the NVIDIA driver is being used, rather than the "nv" or "vesa" driver. Search for (II) LoadModule: "nvidia" Lines from the driver should begin with: (II) NVIDIA(0) Q. How can I increase the amount of data printed in the X log file? A. By default, the NVIDIA X driver prints relatively few messages to stderr and the X log file. If you need to troubleshoot, then it may be helpful to enable more verbose output by using the X command line options -verbose and -logverbose, which can be used to set the verbosity level for the 'stderr' and log file messages, respectively. The NVIDIA X driver will output more messages when the verbosity level is at or above 5 (X defaults to verbosity level 1 for 'stderr' and level 3 for the log file). So, to enable verbose messaging from the NVIDIA X driver to both the log file and 'stderr', you could start X with the verbosity level set to 5, by doing the following % startx -- -verbose 5 -logverbose 5 Q. Where can I get 'gl.h' or 'glx.h' so I can compile OpenGL programs? A. Most systems come with these header files preinstalled. However, NVIDIA provides its own 'gl.h' and 'glx.h' files, which get installed by default as part of driver installation. If you prefer that the NVIDIA-distributed OpenGL header files not be installed, you can pass the --no-opengl-headers option to the 'NVIDIA-Linux-x86-256.29.run' file during installation. Q. Can I receive email notification of new NVIDIA Accelerated Linux Graphics Driver releases? A. Yes. Fill out the form at: http://www.nvidia.com/view.asp?FO=driver_update Q. What is NVIDIA's policy towards development series Linux kernels? A. NVIDIA does not officially support development series kernels. However, all the kernel module source code that interfaces with the Linux kernel is available in the 'kernel/' directory of the '.run' file. NVIDIA encourages members of the Linux community to develop patches to these source files to support development series kernels. A web search will most likely yield several community supported patches. Q. Where can I find the tarballs? A. Plain tarballs are not available. The '.run' file is a tarball with a shell script prepended. You can execute the '.run' file with the --extract-only option to unpack the tarball. Q. How do I tell if I have my kernel sources installed? A. If you are running on a distro that uses RPM (Red Hat, Mandriva, SuSE, etc), then you can use 'rpm' to tell you. At a shell prompt, type: % rpm -qa | grep kernel and look at the output. You should see a package that corresponds to your kernel (often named something like kernel-2.6.15-7) and a kernel source package with the same version (often named something like kernel-devel-2.6.15-7 or kernel-source-2.4.18-3). If none of the lines seem to correspond to a source package, then you will probably need to install it. If the versions listed mismatch (e.g., kernel-2.6.15-7 vs. kernel-devel-2.6.15-10), then you will need to update the kernel-devel package to match the installed kernel. If you have multiple kernels installed, you need to install the kernel-devel package that corresponds to your RUNNING kernel (or make sure your installed source package matches the running kernel). You can do this by looking at the output of 'uname -r' and matching versions. Q. Where can I find older driver versions? A. Please visit ftp://download.nvidia.com/XFree86_40/ Q. What is SELinux and how does it interact with the NVIDIA driver ? A. Security-Enhanced Linux (SELinux) is a set of modifications applied to the Linux kernel and utilities that implement a security policy architecture. When in use it requires that the security type on all shared libraries be set to 'shlib_t'. The installer detects when to set the security type, and sets it on all shared libraries it installs. The option --force-selinux passed to the '.run' file overrides the detection of when to set the security type. Q. Why does X use so much memory? A. When measuring any application's memory usage, you must be careful to distinguish between physical system RAM used and virtual mappings of shared resources. For example, most shared libraries exist only once in physical memory but are mapped into multiple processes. This memory should only be counted once when computing total memory usage. In the same way, the video memory on a graphics card or register memory on any device can be mapped into multiple processes. These mappings do not consume normal system RAM. This has been a frequently discussed topic on XFree86 mailing lists; see, for example: http://marc.theaimsgroup.com/?l=xfree-xpert&m=96835767116567&w=2 The 'pmap' utility described in the above thread is available in the "procps" package shipped with most recent Linux distributions, and is a useful tool in distinguishing between types of memory mappings. For example, while 'top' may indicate that X is using several hundred MB of memory, the last line of output from the output of pmap (note that pmap may need to be run as root): # pmap -d `pidof X` | tail -n 1 mapped: 161404K writeable/private: 7260K shared: 118056K reveals that X is really only using roughly 7MB of system RAM (the "writeable/private" value). Note, also, that X must allocate resources on behalf of X clients (the window manager, your web browser, etc); the X server's memory usage will increase as more clients request resources such as pixmaps, and decrease as you close X applications. The "IndirectMemoryAccess" X configuration option may cause additional virtual address space to be reserved. Q. Why do applications that use DGA graphics fail? A. The NVIDIA driver does not support the graphics component of the XFree86-DGA (Direct Graphics Access) extension. Applications can use the XDGASelectInput() function to acquire relative pointer motion, but graphics-related functions such as XDGASetMode() and XDGAOpenFramebuffer() will fail. The graphics component of XFree86-DGA is not supported because it requires a CPU mapping of framebuffer memory. As graphics cards ship with increasing quantities of video memory, the NVIDIA X driver has had to switch to a more dynamic memory mapping scheme that is incompatible with DGA. Furthermore, DGA does not cooperate with other graphics rendering libraries such as Xlib and OpenGL because it accesses GPU resources directly. NVIDIA recommends that applications use OpenGL or Xlib, rather than DGA, for graphics rendering. Using rendering libraries other than DGA will yield better performance and improve interoperability with other X applications. Q. My kernel log contains messages that are prefixed with "Xid"; what do these messages mean? A. "Xid" messages indicate that a general GPU error occurred, most often due to the driver misprogramming the GPU or to corruption of the commands sent to the GPU. These messages provide diagnostic information that can be used by NVIDIA to aid in debugging reported problems. Q. On what NVIDIA hardware is the EXT_framebuffer_object OpenGL extension supported? A. EXT_framebuffer_object is supported on GeForce FX, Quadro FX, and newer GPUs. Q. I use the Coolbits overclocking interface to adjust my graphics card's clock frequencies, but the defaults are reset whenever X is restarted. How do I make my changes persistent? A. Clock frequency settings are not saved/restored automatically by default to avoid potential stability and other problems that may be encountered if the chosen frequency settings differ from the defaults qualified by the manufacturer. You can use the command line below in '~/.xinitrc' to automatically apply custom clock frequency settings when the X server is started: # nvidia-settings -a GPUOverclockingState=1 -a GPU2DClockFreqs=, -a GPU3DClockFreqs=, Here '' and '' are the desired GPU and video memory frequencies (in MHz), respectively. Q. Why is the refresh rate not reported correctly by utilities that use the XRandR X extension (e.g., the GNOME "Screen Resolution Preferences" panel, `xrandr -q`, etc)? A. The XRandR X extension is not presently aware of multiple display devices on a single X screen; it only sees the MetaMode bounding box, which may contain one or more actual modes. This means that if multiple MetaModes have the same bounding box, XRandR will not be able to distinguish between them. In order to support DynamicTwinView, the NVIDIA X driver must make each MetaMode appear to be unique to XRandR. Presently, the NVIDIA X driver accomplishes this by using the refresh rate as a unique identifier. You can use `nvidia-settings -q RefreshRate` to query the actual refresh rate on each display device. This behavior can be disabled by setting the X configuration option "DynamicTwinView" to FALSE. For details, see Chapter 13. Q. Why does starting certain applications result in Xlib error messages indicating extensions like "XFree86-VidModeExtension" or "SHAPE" are missing? A. If your X config file has a "Module" section that does not list the "extmod" module, some X server extensions may be missing, resulting in error messages of the form: Xlib: extension "SHAPE" missing on display ":0.0" Xlib: extension "XFree86-VidModeExtension" missing on display ":0.0" Xlib: extension "XFree86-DGA" missing on display ":0.0" You can solve this problem by adding the line below to your X config file's "Module" section: Load "extmod" ______________________________________________________________________________ Chapter 8. Common Problems ______________________________________________________________________________ This section provides solutions to common problems associated with the NVIDIA Linux x86 Driver. Q. My X server fails to start, and my X log file contains the error: (EE) NVIDIA(0): The NVIDIA kernel module does not appear to (EE) NVIDIA(0): be receiving interrupts generated by the NVIDIA graphics (EE) NVIDIA(0): device PCI:x:x:x. Please see the COMMON PROBLEMS (EE) NVIDIA(0): section in the README for additional information. A. This can be caused by a variety of problems, such as PCI IRQ routing errors, I/O APIC problems or conflicts with other devices sharing the IRQ (or their drivers). If possible, configure your system such that your graphics card does not share its IRQ with other devices (try moving the graphics card to another slot if applicable, unload/disable the driver(s) for the device(s) sharing the card's IRQ, or remove/disable the device(s)). Depending on the nature of the problem, one of (or a combination of) these kernel parameters might also help: Parameter Behavior -------------- --------------------------------------------------- pci=noacpi don't use ACPI for PCI IRQ routing pci=biosirq use PCI BIOS calls to retrieve the IRQ routing table noapic don't use I/O APICs present in the system acpi=off disable ACPI Q. My X server fails to start, and my X log file contains the error: (EE) NVIDIA(0): The interrupt for NVIDIA graphics device PCI:x:x:x (EE) NVIDIA(0): appears to be edge-triggered. Please see the COMMON (EE) NVIDIA(0): PROBLEMS section in the README for additional information. A. An edge-triggered interrupt means that the kernel has programmed the interrupt as edge-triggered rather than level-triggered in the Advanced Programmable Interrupt Controller (APIC). Edge-triggered interrupts are not intended to be used for sharing an interrupt line between multiple devices; level-triggered interrupts are the intended trigger for such usage. When using edge-triggered interrupts, it is common for device drivers using that interrupt line to stop receiving interrupts. This would appear to the end user as those devices no longer working, and potentially as a full system hang. These problems tend to be more common when multiple devices are sharing that interrupt line. This occurs when ACPI is not used to program interrupt routing in the APIC. This often occurs on 2.4 Linux kernels, which do not fully support ACPI, or 2.6 kernels when ACPI is disabled or fails to initialize. In these cases, the Linux kernel falls back to tables provided by the system BIOS. In some cases the system BIOS assumes ACPI will be used for routing interrupts and configures these tables to incorrectly label all interrupts as edge-triggered. The current interrupt configuration can be found in /proc/interrupts. Available workarounds include: updating to a newer system BIOS, trying a 2.6 kernel with ACPI enabled, or passing the 'noapic' option to the kernel to force interrupt routing through the traditional Programmable Interrupt Controller (PIC). Newer kernels also provide an interrupt polling mechanism to attempt to work around this problem. This mechanism can be enabled by passing the 'irqpoll' option to the kernel. Currently, the NVIDIA driver will attempt to detect edge triggered interrupts and X will purposely fail to start (to avoid stability issues). This behavior can be overridden by setting the "NVreg_RMEdgeIntrCheck" NVIDIA Linux kernel module parameter. This parameter defaults to "1", which enables the edge triggered interrupt detection. Set this parameter to "0" to disable this detection. Q. X starts for me, but OpenGL applications terminate immediately. A. If X starts but you have trouble with OpenGL, you most likely have a problem with other libraries in the way, or there are stale symlinks. See Chapter 5 for details. Sometimes, all it takes is to rerun 'ldconfig'. You should also check that the correct extensions are present; % xdpyinfo should show the "GLX" and "NV-GLX" extensions present. If these two extensions are not present, then there is most likely a problem loading the glx module, or it is unable to implicitly load GLcore. Check your X config file and make sure that you are loading glx (see Chapter 6). If your X config file is correct, then check the X log file for warnings/errors pertaining to GLX. Also check that all of the necessary symlinks are in place (refer to Chapter 5). Q. When Xinerama is enabled, my stereo glasses are shuttering only when the stereo application is displayed on one specific X screen. When the application is displayed on the other X screens, the stereo glasses stop shuttering. A. This problem occurs with DDC and "blue line" stereo glasses, that get the stereo signal from one video port of the graphics card. When a X screen does not display any stereo drawable the stereo signal is disabled on the associated video port. Forcing stereo flipping allows the stereo glasses to shutter continuously. This can be done by enabling the OpenGL control "Force Stereo Flipping" in nvidia-settings, or by setting the X configuration option "ForceStereoFlipping" to "1". Q. Stereo is not in sync across multiple displays. A. There are two cases where this may occur. If the displays are attached to the same GPU, and one of them is out of sync with the stereo glasses, you will need to reconfigure your monitors to drive identical mode timings; see Chapter 19 for details. If the displays are attached to different GPUs, the only way to synchronize stereo across the displays is with a G-Sync device, which is only supported by certain Quadro cards. See Chapter 26 for details. This applies to seperate GPUs on seperate cards as well as seperate GPUs on the same card, such as Quadro FX 4500 X2. Note that the Quadro FX 4500 X2 only provides a single DIN connector for stereo, tied to the bottommost GPU. In order to synchronize onboard stereo on the other GPU you must use a G-Sync device. Q. I just upgraded my kernel, and now the NVIDIA kernel module will not load. A. The kernel interface layer of the NVIDIA kernel module must be compiled specifically for the configuration and version of your kernel. If you upgrade your kernel, then the simplest solution is to reinstall the driver. ADVANCED: You can install the NVIDIA kernel module for a non running kernel (for example: in the situation where you just built and installed a new kernel, but have not rebooted yet) with a command line such as this: # sh NVIDIA-Linux-x86-256.29.run --kernel-name='KERNEL_NAME' Where 'KERNEL_NAME' is what 'uname -r' would report if the target kernel were running. Q. My X server fails to start, and my X log file contains the error: (EE) NVIDIA(0): Failed to load the NVIDIA kernel module! A. The X driver will abort with this error message if the NVIDIA kernel module fails to load. If you receive this error, you should check the output of `dmesg` for kernel error messages and/or attempt to load the kernel module explicitly with `modprobe nvidia`. If unresolved symbols are reported, then the kernel module was most likely built against a Linux kernel source tree (or kernel headers) for a kernel revision or configuration that doesn't match the running kernel. You can specify the location of the kernel source tree (or headers) when you install the NVIDIA driver using the --kernel-source-path command line option (see `sh NVIDIA-Linux-x86-256.29.run --advanced-options` for details). Old versions of the module-init-tools include `modprobe` binaries that report an error when instructed to load a module that's already loaded into the kernel. Please upgrade your module-init-tools if you receive an error message to this effect. The X server reads '/proc/sys/kernel/modprobe' to determine the path to the `modprobe` utility and falls back to '/sbin/modprobe' if the file doesn't exist. Please make sure that this path is valid and refers to a `modprobe` binary compatible with the Linux kernel running on your system. Q. Installing the NVIDIA kernel module gives an error message like: #error Modules should never use kernel-headers system headers #error but headers from an appropriate kernel-source A. You need to install the source for the Linux kernel. In most situations you can fix this problem by installing the kernel-source or kernel-devel package for your distribution Q. OpenGL applications crash and print out the following warning: WARNING: Your system is running with a buggy dynamic loader. This may cause crashes in certain applications. If you experience crashes you can try setting the environment variable __GL_SINGLE_THREADED to 1. For more information, consult the FREQUENTLY ASKED QUESTIONS section in the file /usr/share/doc/NVIDIA_GLX-1.0/README.txt. A. The dynamic loader on your system has a bug which will cause applications linked with pthreads, and that dlopen() libGL multiple times, to crash. This bug is present in older versions of the dynamic loader. Distributions that shipped with this loader include but are not limited to Red Hat Linux 6.2 and Mandrake Linux 7.1. Version 2.2 and later of the dynamic loader are known to work properly. If the crashing application is single threaded then setting the environment variable '__GL_SINGLE_THREADED' to "1" will prevent the crash. In the bash shell you would enter: % export __GL_SINGLE_THREADED=1 and in csh and derivatives use: % setenv __GL_SINGLE_THREADED 1 Previous releases of the NVIDIA Accelerated Linux Graphics Driver attempted to work around this problem. Unfortunately, the workaround caused problems with other applications and was removed after version 1.0-1541. Q. Quake3 crashes when changing video modes. A. You are probably experiencing a problem described above. Please check the text output for the "WARNING" message described in the previous hint. Setting '__GL_SINGLE_THREADED' to "1" as will fix the problem. Q. I cannot build the NVIDIA kernel module, or, I can build the NVIDIA kernel module, but modprobe/insmod fails to load the module into my kernel. A. These problems are generally caused by the build using the wrong kernel header files (i.e. header files for a different kernel version than the one you are running). The convention used to be that kernel header files should be stored in '/usr/include/linux/', but that is deprecated in favor of '/lib/modules/RELEASE/build/include' (where RELEASE is the result of 'uname -r'. The 'nvidia-installer' should be able to determine the location on your system; however, if you encounter a problem you can force the build to use certain header files by using the --kernel-include-dir option. For this to work you will of course need the appropriate kernel header files installed on your system. Consult the documentation that came with your distribution; some distributions do not install the kernel header files by default, or they install headers that do not coincide properly with the kernel you are running. Q. There are problems running Heretic II. A. Heretic II installs, by default, a symlink called 'libGL.so' in the application directory. You can remove or rename this symlink, since the system will then find the default 'libGL.so' (which our drivers install in '/usr/lib'). From within Heretic II you can then set your render mode to OpenGL in the video menu. There is also a patch available to Heretic II from lokigames at: http://www.lokigames.com/products/heretic2/updates.php3/ Q. My system hangs when switching to a virtual terminal if I have rivafb enabled. A. Using both rivafb and the NVIDIA kernel module at the same time is currently broken. In general, using two independent software drivers to drive the same piece of hardware is a bad idea. Q. Compiling the NVIDIA kernel module gives this error: You appear to be compiling the NVIDIA kernel module with a compiler different from the one that was used to compile the running kernel. This may be perfectly fine, but there are cases where this can lead to unexpected behavior and system crashes. If you know what you are doing and want to override this check, you can do so by setting IGNORE_CC_MISMATCH. In any other case, set the CC environment variable to the name of the compiler that was used to compile the kernel. A. You should compile the NVIDIA kernel module with the same compiler version that was used to compile your kernel. Some Linux kernel data structures are dependent on the version of gcc used to compile it; for example, in 'include/linux/spinlock.h': ... * Most gcc versions have a nasty bug with empty initializers. */ #if (__GNUC__ > 2) typedef struct { } rwlock_t; #define RW_LOCK_UNLOCKED (rwlock_t) { } #else typedef struct { int gcc_is_buggy; } rwlock_t; #define RW_LOCK_UNLOCKED (rwlock_t) { 0 } #endif If the kernel is compiled with gcc 2.x, but gcc 3.x is used when the kernel interface is compiled (or vice versa), the size of rwlock_t will vary, and things like ioremap will fail. To check what version of gcc was used to compile your kernel, you can examine the output of: % cat /proc/version To check what version of gcc is currently in your '$PATH', you can examine the output of: % gcc -v Q. X fails with error Failed to allocate LUT context DMA A. This is one of the possible consequences of compiling the NVIDIA kernel interface with a different gcc version than used to compile the Linux kernel (see above). Q. I recently updated various libraries on my system using my Linux distributor's update utility, and the NVIDIA graphics driver no longer works. A. Conflicting libraries may have been installed by your distribution's update utility; see Chapter 5 for details on how to diagnose this. Q. I have rebuilt the NVIDIA kernel module, but when I try to insert it, I get a message telling me I have unresolved symbols. A. Unresolved symbols are most often caused by a mismatch between your kernel sources and your running kernel. They must match for the NVIDIA kernel module to build correctly. Make sure your kernel sources are installed and configured to match your running kernel. Q. I am unable to load the NVIDIA kernel module that I compiled for the Red Hat Linux 7.3 2.4.18-3bigmem kernel. A. The kernel header files Red Hat Linux distributes for Red Hat Linux 7.3 2.4.18-3bigmem kernel are misconfigured. NVIDIA's precompiled kernel module for this kernel can be loaded, but if you want to compile the NVIDIA kernel interface files yourself for this kernel, then you will need to perform the following: # cd /lib/modules/`uname -r`/build/ # make mrproper # cp configs/kernel-2.4.18-i686-bigmem.config .config # make oldconfig dep Note: Red Hat Linux ships kernel header files that are simultaneously configured for ALL of their kernels for a particular distribution version. A header file generated at boot time sets up a few parameters that select the correct configuration. Rebuilding the kernel headers with the above commands will create header files suitable for the Red Hat Linux 7.3 2.4.18-3bigmem kernel configuration only, thus making the header files for the other configurations unusable. Q. OpenGL applications leak significant amounts of memory on my system! A. If your kernel is making use of the -rmap VM, the system may be leaking memory due to a memory management optimization introduced in -rmap14a. The -rmap VM has been adopted by several popular distributions, the memory leak is known to be present in some of the distribution kernels; it has been fixed in -rmap15e. If you suspect that your system is affected, try upgrading your kernel or contact your distribution's vendor for assistance. Q. Some OpenGL applications (like Quake3 Arena) crash when I start them on Red Hat Linux 9.0. A. Some versions of the glibc package shipped by Red Hat that support TLS do not properly handle using dlopen() to access shared libraries which use some TLS models. This problem is exhibited, for example, when Quake3 Area dlopen() 's NVIDIA's libGL library. Please obtain at least glibc-2.3.2-11.9 which is available as an update from Red Hat. Q. I have installed the driver, but my Enable 3D Acceleration check box is still grayed out. A. Most distribution-provided configuration applets are not aware of the NVIDIA accelerated driver, and consequently will not update themselves when you install the driver. Your driver, if it has been installed properly, should function fine. Q. When changing settings in games like Quake 3 Arena, or Wolfenstein Enemy Territory, the game crashes and I see this error: ...loading libGL.so.1: QGL_Init: dlopen libGL.so.1 failed: /usr/lib/tls/libGL.so.1: shared object cannot be dlopen()ed: static TLS memory too small A. These games close and reopen the NVIDIA OpenGL driver (via dlopen() / dlclose()) when settings are changed. On some versions of glibc (such as the one shipped with Red Hat Linux 9), there is a bug that leaks static TLS entries. This glibc bug causes subsequent re-loadings of the OpenGL driver to fail. This is fixed in more recent versions of glibc; see Red Hat bug #89692: https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=89692 Q. X crashes during 'startx', and my X log file contains this error message: (EE) NVIDIA(0): Failed to obtain a shared memory identifier. A. The NVIDIA OpenGL driver and the NVIDIA X driver require shared memory to communicate; you must have 'CONFIG_SYSVIPC' enabled in your kernel. Q. When I try to install the driver, the installer claims that X is running, even though I have exited X. A. The installer detects the presence of an X server by checking for the X server's lock files: '/tmp/.Xn-lock', where 'n' is the number of the X Display (the installer checks for X Displays 0-7). If you have exited X, but one of these files has been left behind, then you will need to manually delete the lock file. DO NOT remove this file if X is still running! Q. My system runs, but seems unstable. A. Your stability problems may be AGP-related. See Chapter 12 for details. Q. OpenGL applications are running slowly A. The application is probably using a different library that still remains on your system, rather than the NVIDIA supplied OpenGL library. See Chapter 5 for details. Q. There are problems running Quake2. A. Quake2 requires some minor setup to get it going. First, in the Quake2 directory, the install creates a symlink called 'libGL.so' that points at 'libMesaGL.so'. This symlink should be removed or renamed. Second, in order to run Quake2 in OpenGL mode, you must type % quake2 +set vid_ref glx +set gl_driver libGL.so Quake2 does not seem to support any kind of full-screen mode, but you can run your X server at the same resolution as Quake2 to emulate full-screen mode. Q. X takes a long time to start (possibly several minutes). A. Most of the X startup delay problems we have found are caused by incorrect data in video BIOSes about what display devices are possibly connected or what i2c port should be used for detection. You can work around these problems with the X config option IgnoreDisplayDevices (see the description in Appendix B). Q. Fonts are incorrectly sized after installing the NVIDIA driver. A. Incorrectly sized fonts are generally caused by incorrect DPI (Dots Per Inch) information. You can check what X thinks the physical size of your monitor is, by running: % xdpyinfo | grep dimensions This will report the size in pixels, and in millimeters. If these numbers are wrong, you can correct them by modifying the X server's DPI setting. See Appendix E for details. Q. General problems with ALi chipsets A. There are some known timing and signal integrity issues on ALi chipsets. The following tips may help stabilize problematic ALI systems: o Disable TURBO AGP MODE in the BIOS. o When using a P5A upgrade to BIOS Revision 1002 BETA 2. o When using 1007, 1007A or 1009 adjust the IO Recovery Time to 4 cycles. o AGP is disabled by default on some ALi chipsets (ALi1541, ALi1647) to work around severe system stability problems with these chipsets. See the comments for EnableALiAGP in 'nv-reg.h' to force AGP on anyway. Q. Using GNOME configuration utilities, I am unable to get a resolution above 800x600. A. The installation of GNOME provided in operating systems such as Red Hat Enterprise Linux 4 contain several competing interfaces for specifying resolution: 'System Settings' -> 'Display' which will update the X configuration file, and 'Applications' -> 'Preferences' -> 'Screen Resolution' which will update the per-user screen resolution using the XRandR extension. Your desktop resolution will be limited to the smaller of the two settings. Be sure to check the setting of each. Q. X does not restore the VGA console when run on a TV. I get this error message in my X log file: Unable to initialize the X int10 module; the console may not be restored correctly on your TV. A. The NVIDIA X driver uses the X Int10 module to save and restore console state on TV out, and will not be able to restore the console correctly if it cannot use the Int10 module. If you have built the X server yourself, please be sure you have built the Int10 module. If you are using a build of the X server provided by your operating system and are missing the Int10 module, contact your operating system distributor. Q. OpenGL applications don't work, and my X log file contains the error: (EE) NVIDIA(0): Unable to map device node /dev/zero with read, write, and (EE) NVIDIA(0): execute privileges. The GLX extension will be disabled (EE) NVIDIA(0): on this X screen. Please see the COMMON PROBLEMS (EE) NVIDIA(0): section in the README for more information. A. The NVIDIA OpenGL driver must be able to map the '/dev/zero' device node with read, write, and execute privileges in order to function correctly. The driver needs this ability to allocate executable memory, which is used for optimizations that require generating code at run-time. Currently, GLX cannot run without these optimizations. Check that your '/dev' filesystem is set up correctly. In particular, mounting the '/dev' file system with the 'noexec' option will cause this to happen. If you haven't changed the configuration of your '/dev' filesystem, please contact your operating system distributor. Q. X doesn't start, and my log file contains a message like the following: (EE) NVIDIA(0): Failed to allocate primary buffer: failed to set CPU access (EE) NVIDIA(0): for surface. Please see Chapter 8: Common Problems in (EE) NVIDIA(0): the README for troubleshooting suggestions. A. The NVIDIA X driver needs to be able to access the buffers it allocates from the CPU, but wasn't able to set up this access. This commonly fails if you're using a large virtual desktop size. Although your GPU may have enough onboard video memory for the buffer, the amount of usable memory may be limited if the "IndirectMemoryAccess" option is disabled, or if not enough address space was reserved for indirect memory access (this commonly occurs on 32-bit systems). If you're seeing this problem and are using a 32-bit operating system, it may be resolved by switching to a 64-bit operating system. ______________________________________________________________________________ Chapter 9. Known Issues ______________________________________________________________________________ The following problems still exist in this release and are in the process of being resolved. Known Issues OpenGL and dlopen() There are some issues with older versions of the glibc dynamic loader (e.g., the version that shipped with Red Hat Linux 7.2) and applications such as Quake3 and Radiant, that use dlopen(). See Chapter 7 for more details. Multicard, Multimonitor In some cases, the secondary card is not initialized correctly by the NVIDIA kernel module. You can work around this by enabling the XFree86 Int10 module to soft-boot all secondary cards. See Appendix B for details. Interaction with pthreads Single-threaded applications that use dlopen() to load NVIDIA's libGL library, and then use dlopen() to load any other library that is linked against libpthread will crash in libGL. This does not happen in NVIDIA's new ELF TLS OpenGL libraries (see Chapter 5 for a description of the ELF TLS OpenGL libraries). Possible workarounds for this problem are: 1. Load the library that is linked with libpthread before loading libGL. 2. Link the application with libpthread. The X86-64 platform (AMD64/EM64T) and 2.6 kernels Many 2.4 and 2.6 x86_64 kernels have an accounting problem in their implementation of the change_page_attr kernel interface. Early 2.6 kernels include a check that triggers a BUG() when this situation is encountered (triggering a BUG() results in the current application being killed by the kernel; this application would be your OpenGL application or potentially the X server). The accounting issue has been resolved in the 2.6.11 kernel. We have added checks to recognize that the NVIDIA kernel module is being compiled for the x86-64 platform on a kernel between 2.6.0 and 2.6.11. In this case, we will disable usage of the change_page_attr kernel interface. This will avoid the accounting issue but leaves the system in danger of cache aliasing (see entry below on Cache Aliasing for more information about cache aliasing). Note that this change_page_attr accounting issue and BUG() can be triggered by other kernel subsystems that rely on this interface. If you are using a 2.6 x86_64 kernel, it is recommended that you upgrade to a 2.6.11 or later kernel. Also take note of common dma issues on 64-bit platforms in Chapter 10. Cache Aliasing Cache aliasing occurs when multiple mappings to a physical page of memory have conflicting caching states, such as cached and uncached. Due to these conflicting states, data in that physical page may become corrupted when the processor's cache is flushed. If that page is being used for DMA by a driver such as NVIDIA's graphics driver, this can lead to hardware stability problems and system lockups. NVIDIA has encountered bugs with some Linux kernel versions that lead to cache aliasing. Although some systems will run perfectly fine when cache aliasing occurs, other systems will experience severe stability problems, including random lockups. Users experiencing stability problems due to cache aliasing will benefit from updating to a kernel that does not cause cache aliasing to occur. NVIDIA has added driver logic to detect cache aliasing and to print a warning with a message similar to the following: NVRM: bad caching on address 0x1cdf000: actual 0x46 != expected 0x73 If you see this message in your log files and are experiencing stability problems, you should update your kernel to the latest version. If the message persists after updating your kernel, send a bug report to NVIDIA. 64-Bit BARs (Base Address Registers) Starting with native PCI Express GPUs, NVIDIA's GPUs will advertise a 64-bit BAR capability (a Base Address Register stores the location of a PCI I/O region, such as registers or a frame buffer). This means that the GPU's PCI I/O regions (registers and frame buffer) can be placed above the 32-bit address space (the first 4 gigabytes of memory). The decision of where the BAR is placed is made by the system BIOS at boot time. If the BIOS supports 64-bit BARs, then the NVIDIA PCI I/O regions may be placed above the 32-bit address space. If the BIOS does not support this feature, then our PCI I/O regions will be placed within the 32-bit address space as they have always been. Unfortunately, current Linux kernels (as of 2.6.11.x) do not understand or support 64-bit BARs. If the BIOS does place any NVIDIA PCI I/O regions above the 32-bit address space, the kernel will reject the BAR and the NVIDIA driver will not work. There is no known workaround at this point. Kernel virtual address space exhaustion on the X86 platform On X86 systems and AMD64/EM64T systems using X86 kernels, only 4GB of virtual address space are available, which the Linux kernel typically partitions such that user processes are allocated 3GB, the kernel itself 1GB. Part of the kernel's share is used to create a direct mapping of system memory (RAM). Depending on how much system memory is installed, the kernel virtual address space remaining for other uses varies in size and may be as small as 128MB, if 1GB of system memory (or more) are installed. By default, the kernel reserves a minimum of 128MB. The kernel virtual address space still available after the creation of the direct system memory mapping is used by both the kernel and by drivers to map I/O resources, and for some memory allocations. Depending on the number of consumers and their respective requirements, the Linux kernel's virtual address space may be exhausted. Newer Linux kernels print an error message of the form below when this happens: allocation failed: out of vmalloc space - use vmalloc= to increase size. The NVIDIA kernel module requires portions of the kernel's virtual address space for each GPU and for certain memory allocations. If no more than 128MB are available to the kernel and device drivers at boot time, the NVIDIA kernel module may be unable to initialize all GPUs, or fail memory allocations. This is not usually a problem with only 1 or 2 GPUs, however depending on the number of other drivers and their usage patterns, it can be; it is likely to be a problem with 3 or more GPUs. Possible solutions for this problem include: o If available, the 'vmalloc' kernel parameter can be used to increase the size of the kernel virtual address space reserved by the Linux kernel (the default is 128MB). Incrementally raising this to find the best balance between the size of the kernel virtual address space made available and the size of the direct system memory mapping is recommended. You can achieve this by passing 'vmalloc=192M', 'vmalloc=256MB', ..., to the kernel and checking if the above error message continues to be printed. Note that some versions of the GRUB boot loader have problems calculating the memory layout and loading the initrd if the 'vmalloc' kernel parameter is used. The 'uppermem' GRUB command can be used to force GRUB to load the initrd into a lower region of system memory to work around this problem. This will not adversely affect system performance once the kernel has been loaded. The suggested syntax is: title Kernel Title uppermem 524288 kernel (hdX,Y)/boot/vmlinuz... Also note that the 'vmalloc' kernel parameter only exists on Linux 2.6.9 and later kernels. On older kernels, the amount of system memory used by the kernel can be reduced with the 'mem' kernel parameter, which also reduces the size of the direct mapping and thus increases the size of the kernel virtual address space available. For example, 'mem=512M' instructs the kernel to ignore all but the first 512MB of system memory. Although it is undesirable to reduce the amount of usable system memory, this approach can be used to check if initialization problems are caused by kernel virtual address space exhaustion. o In some cases, disabling frame buffer drivers such as vesafb can help, as such drivers may attempt to map all or a large part of the installed graphics cards' video memory into the kernel's virtual address space, which rapidly consumes this resource. You can disable the vesafb frame buffer driver by passing these parameters to the kernel: 'video=vesa:off vga=normal'. o Some Linux kernels can be configured with alternate address space layouts (e.g. 2.8GB:1.2GB, 2GB:2GB, etc.). This option can be used to avoid exhaustion of the kernel virtual address space without reducing the size of the direct system memory mapping. Some Linux distributors also provide kernels that use seperate 4GB address spaces for user processes and the kernel. Such Linux kernels provide sufficient kernel virtual address space on typical systems. o If your system is equipped with an X86-64 (AMD64/EM64T) processor, it is recommended that you switch to a 64-bit Linux kernel/distribution. Due to the significantly larger address space provided by the X86-64 processors' addressing capabilities, X86-64 kernels will not run out of kernel virtual address space in the foreseeable future. Valgrind The NVIDIA OpenGL implementation makes use of self modifying code. To force Valgrind to retranslate this code after a modification you must run using the Valgrind command line option: --smc-check=all Without this option Valgrind may execute incorrect code causing incorrect behavior and reports of the form: ==30313== Invalid write of size 4 MMConfig-based PCI Configuration Space Accesses 2.6 kernels have added support for Memory-Mapped PCI Configuration Space accesses. Unfortunately, there are many problems with this mechanism, and the latest kernel updates are more careful about enabling this support. The NVIDIA driver may be unable to reliably read/write the PCI Configuration Space of NVIDIA devices when the kernel is using the MMCONFIG method to access PCI Configuration Space, specifically when using multiple GPUs and multiple CPUs on 32-bit kernels. This access method can be identified by the presence of the string "PCI: Using MMCONFIG" in the 'dmesg' output on your system. This access method can be disabled via the "pci=nommconf" kernel parameter. Notebooks If you are using a notebook see the "Known Notebook Issues" in Chapter 18. FSAA When FSAA is enabled (the __GL_FSAA_MODE environment variable is set to a value that enables FSAA and a multisample visual is chosen), the rendering may be corrupted when resizing the window. libGL DSO finalizer and pthreads When a multithreaded OpenGL application exits, it is possible for libGL's DSO finalizer (also known as the destructor, or "_fini") to be called while other threads are executing OpenGL code. The finalizer needs to free resources allocated by libGL. This can cause problems for threads that are still using these resources. Setting the environment variable "__GL_NO_DSO_FINALIZER" to "1" will work around this problem by forcing libGL's finalizer to leave its resources in place. These resources will still be reclaimed by the operating system when the process exits. Note that the finalizer is also executed as part of dlclose(3), so if you have an application that dlopens(3) and dlcloses(3) libGL repeatedly, "__GL_NO_DSO_FINALIZER" will cause libGL to leak resources until the process exits. Using this option can improve stability in some multithreaded applications, including Java3D applications. XVideo and the Composite X extension XVideo will not work correctly when Composite is enabled unless using X.Org 7.1 or later. See Chapter 23. GLX visuals in Xinerama X servers prior to version 1.5.0 have a limitation in the number of visuals that can be available when Xinerama is enabled. Specifically, visuals with ID values over 255 will cause the server to corrupt memory, leading to incorrect behavior or crashes. In some configurations where many GLX features are enabled at once, the number of GLX visuals will exceed this limit. To avoid a crash, the NVIDIA X driver will discard visuals above the limit. To see which visuals are being discarded, run the X server with the -logverbose 6 option and then check the X server log file. Some X servers have trouble with multiple GPUs Some versions of the X.Org server version 1.5.0 and higher have a bug that causes X to fail with an error similar to the following when there is more than one GPU in the computer: (!!) More than one possible primary device found (II) Primary Device is: (EE) No devices detected. Fatal server error: no screens found You can work around this problem by specifying the bus ID of the device you wish to use. For more details, please search the xorg.conf manual page for "BusID". You can configure the X server with an X screen on each NVIDIA GPU by running: nvidia-xconfig --enable-all-gpus Please see http://bugs.freedesktop.org/show_bug.cgi?id=18321 for more details on this X server problem. This section describes problems that will not be fixed. Usually, the source of the problem is beyond the control of NVIDIA. Following is the list of problems: Problems that Will Not Be Fixed Gigabyte GA-6BX Motherboard This motherboard uses a LinFinity regulator on the 3.3 V rail that is only rated to 5 A -- less than the AGP specification, which requires 6 A. When diagnostics or applications are running, the temperature of the regulator rises, causing the voltage to the NVIDIA GPU to drop as low as 2.2 V. Under these circumstances, the regulator cannot supply the current on the 3.3 V rail that the NVIDIA GPU requires. This problem does not occur when the graphics card has a switching regulator or when an external power supply is connected to the 3.3 V rail. VIA KX133 and 694X Chip sets with AGP 2x On Athlon motherboards with the VIA KX133 or 694X chip set, such as the ASUS K7V motherboard, NVIDIA drivers default to AGP 2x mode to work around insufficient drive strength on one of the signals. Irongate Chip sets with AGP 1x AGP 1x transfers are used on Athlon motherboards with the Irongate chipset to work around a problem with signal integrity. ALi chipsets, ALi1541 and ALi1647 On ALi1541 and ALi1647 chipsets, NVIDIA drivers disable AGP to work around timing issues and signal integrity issues. See Chapter 8 for more information on ALi chipsets. NV-CONTROL versions 1.8 and 1.9 Version 1.8 of the NV-CONTROL X Extension introduced target types for setting and querying attributes as well as receiving event notification on targets. Targets are objects like X Screens, GPUs and G-Sync devices. Previously, all attributes were described relative to an X Screen. These new bits of information (target type and target id) were packed in a non-compatible way in the protocol stream such that addressing X Screen 1 or higher would generate an X protocol error when mixing NV-CONTROL client and server versions. This packing problem has been fixed in the NV-CONTROL 1.10 protocol, making it possible for the older (1.7 and prior) clients to communicate with NV-CONTROL 1.10 servers. Furthermore, the NV-CONTROL 1.10 client library has been updated to accommodate the target protocol packing bug when communicating with a 1.8 or 1.9 NV-CONTROL server. This means that the NV-CONTROL 1.10 client library should be able to communicate with any version of the NV-CONTROL server. NVIDIA recommends that NV-CONTROL client applications relink with version 1.10 or later of the NV-CONTROL client library (libXNVCtrl.a, in the nvidia-settings-256.29.tar.bz2 tarball). The version of the client library can be determined by checking the NV_CONTROL_MAJOR and NV_CONTROL_MINOR definitions in the accompanying nv_control.h. The only web released NVIDIA Linux driver that is affected by this problem (i.e., the only driver to use either version 1.8 or 1.9 of the NV-CONTROL X extension) is 1.0-8756. CPU throttling reducing memory bandwidth on IGP systems For some models of CPU, the CPU throttling technology may affect not only CPU core frequency, but also memory frequency/bandwidth. On systems using integrated graphics, any reduction in memory bandwidth will affect the GPU as well as the CPU. This can negatively affect applications that use significant memory bandwidth, such as video decoding using VDPAU, or certain OpenGL operations. This may cause such applications to run with lower performance than desired. To work around this problem, NVIDIA recommends configuring your CPU throttling implementation to avoid reducing memory bandwidth. This may be as simple as setting a certain minimum frequency for the CPU. Depending on your operating system and/or distribution, this may be as simple as writing to a configuration file in the /sys or /proc filesystems, or other system configuration file. Please read, or search the Internet for, documentation regarding CPU throttling on your operating system. VDPAU initialization failures on supported GPUs If VDPAU gives the VDP_STATUS_NO_IMPLEMENTATION error message on a GPU which was labeled or specified as supporting PureVideo or PureVideo HD, one possible reason is a hardware defect. After ruling out any other software problems, NVIDIA recommends returning the GPU to the manufacturer for a replacement. Some applications, such as Quake 3, crash after querying the OpenGL extension string Some applications have bugs that are triggered when the extension string is longer than a certain size. As more features are added to the driver, the length of this string increases and can trigger these sorts of bugs. You can limit the extensions listed in the OpenGL extension string to the ones that appeared in a particular version of the driver by setting the "__GL_ExtensionStringVersion" environment variable to a particular version number. For example, __GL_ExtensionStringVersion=17700 quake3 will run Quake 3 with the extension string that appeared in the 177.* driver series. Limiting the size of the extension string can work around this sort of application bug. I/O APIC (SMP) If you are experiencing stability problems with a Linux SMP computer and seeing I/O APIC warning messages from the Linux kernel, system reliability may be greatly improved by setting the "noapic" kernel parameter. Local APIC (UP) On some systems, setting the "Local APIC Support on Uniprocessors" kernel configuration option can have adverse effects on system stability and performance. If you are experiencing lockups with a Linux UP computer and have this option set, try disabling local APIC support. nForce2 Chipsets and AGPGART Some of the earlier versions of agpgart to support the nForce2 chipset are known to contain bugs that result in system hangs. The suggested workaround is to use NVAGP or update to a newer kernel. Known problematic versions include all known Red Hat Enterprise Linux 3 kernels (through Update 7). If a broken agpgart is used on an nForce2 chipset, the NVIDIA driver will attempt to work around these agpgart bugs as best it can, by recovering from AGP errors and eventually disabling AGP. To configure NVAGP, see Chapter 12. ______________________________________________________________________________ Chapter 10. Allocating DMA Buffers on 64-bit Platforms ______________________________________________________________________________ NVIDIA GPUs have limits on how much physical memory they can address. This directly impacts DMA buffers, as a DMA buffer allocated in physical memory that is unaddressable by the NVIDIA GPU cannot be used (or may be truncated, resulting in bad memory accesses). All pre-PCI Express GPUs and non-Native PCI Express GPUs (often known as bridged GPUs) are limited to 32 bits of physical address space, which corresponds to 4 GB of memory. On a system with greater than 4 GB of memory, allocating usable DMA buffers can be a problem. Native PCI Express GPUs are capable of addressing greater than 32 bits of physical address space and do not experience the same problems. Newer kernels provide a simple way to allocate memory that is guaranteed to reside within the 32 bit physical address space. Kernel 2.6.15 provides this functionality with the __GFP_DMA32 interface. Kernels earlier than this version provide a software I/O TLB on Intel's EM64T and IOMMU support on AMD's AMD64 platform. Unfortunately, some problems exist with both interfaces. Early implementations of the Linux SWIOTLB set aside a very small amount of memory for its memory pool (only 4 MB). Also, when this memory pool is exhausted, some SWIOTLB implementations forcibly panic the kernel. This is also true for some implementations of the IOMMU interface. Kernel panics and related stability problems on Intel's EM64T platform can be avoided by increasing the size of the SWIOTLB pool with the 'swiotlb' kernel parameter. This kernel parameter expects the desired size as a number of 4 KB pages. NVIDIA suggests raising the size of the SWIOTLB pool to 64 MB; this is accomplished by passing 'swiotlb=16384' to the kernel. note that newer Linux 2.6 kernels already default to a 64 MB SWIOTLB pool, see below for more information. Starting with Linux 2.6.9, the default size of the SWIOTLB is 64 MB and overflow handling is improved. Both of these changes are expected to greatly improve stability on Intel's EM64T platform. If you consider upgrading your Linux kernel to benefit from these improvements, NVIDIA recommends that you upgrade to Linux 2.6.11 or a more recent Linux kernel. See the previous section for additional information. On AMD's AMD64 platform, the size of the IOMMU can be configured in the system BIOS or, if no IOMMU BIOS option is available, using the 'iommu=memaper' kernel parameter. This kernel parameter expects an order and instructs the Linux kernel to create an IOMMU of size 32 MB^order overlapping physical memory. If the system's default IOMMU is smaller than 64 MB, the Linux kernel automatically replaces it with a 64 MB IOMMU. To reduce the risk of stability problems as a result of IOMMU or SWIOTLB exhaustion on the X86-64 platform, the NVIDIA Linux driver internally limits its use of these interfaces. By default, the driver will not use more than 60 MB of IOMMU/SWIOTLB space, leaving 4 MB for the rest of the system (assuming a 64 MB IOMMU/SWIOTLB). This limit can be adjusted with the 'NVreg_RemapLimit' NVIDIA kernel module option. Specifically, if the IOMMU/SWIOTLB is larger than 64 MB, the limit can be adjusted to take advantage of the additional space. The 'NVreg_RemapLimit' option expects the size argument in bytes. NVIDIA recommends leaving 4 MB available for the rest of the system when changing the limit. For example, if the internal limit is to be relaxed to account for a 128 MB IOMMU/SWIOTLB, the recommended remap limit is 124 MB. This remap limit can be specified by passing 'NVreg_RemapLimit=0x7c00000' to the NVIDIA kernel module. Also see the 'The X86-64 platform (AMD64/EM64T) and 2.6 kernels' section in Chapter 9. ______________________________________________________________________________ Chapter 11. Specifying OpenGL Environment Variable Settings ______________________________________________________________________________ 11A. FULL SCENE ANTIALIASING Antialiasing is a technique used to smooth the edges of objects in a scene to reduce the jagged "stairstep" effect that sometimes appears. By setting the appropriate environment variable, you can enable full-scene antialiasing in any OpenGL application on these GPUs. Several antialiasing methods are available and you can select between them by setting the __GL_FSAA_MODE environment variable appropriately. Note that increasing the number of samples taken during FSAA rendering may decrease performance. To see the available values for __GL_FSAA_MODE along with their descriptions, run: nvidia-settings --query=fsaa --verbose The __GL_FSAA_MODE environment variable uses the same integer values that are used to configure FSAA through nvidia-settings and the NV-CONTROL X extension. In other words, these two commands are equivalent: export __GL_FSAA_MODE=5 nvidia-settings --assign FSAA=5 Note that there are three FSAA related configuration attributes (FSAA, FSAAAppControlled and FSAAAppEnhanced) which together determine how a GL application will behave. If FSAAAppControlled is 1, the FSAA specified through nvidia-settings will be ignored, in favor of what the application requests through FBConfig selection. If FSAAAppControlled is 0 but FSAAAppEnhanced is 1, then the FSAA value specified through nvidia-settings will only be applied if the application selected a multisample FBConfig. Therefore, to be completely correct, the nvidia-settings command line to unconditionally assign FSAA should be: nvidia-settings --assign FSAA=5 --assign FSAAAppControlled=0 --assign FSAAAppEnhanced=0 11B. ANISOTROPIC TEXTURE FILTERING Automatic anisotropic texture filtering can be enabled by setting the environment variable __GL_LOG_MAX_ANISO. The possible values are: __GL_LOG_MAX_ANISO Filtering Type ---------------------------------- ---------------------------------- 0 No anisotropic filtering 1 2x anisotropic filtering 2 4x anisotropic filtering 3 8x anisotropic filtering 4 16x anisotropic filtering 4x and greater are only available on GeForce3 or newer GPUs; 16x is only available on GeForce 6800 or newer GPUs. 11C. VBLANK SYNCING Setting the environment variable __GL_SYNC_TO_VBLANK to a non-zero value will force glXSwapBuffers to sync to your monitor's vertical refresh (perform a swap only during the vertical blanking period). When using __GL_SYNC_TO_VBLANK with TwinView, OpenGL can only sync to one of the display devices; this may cause tearing corruption on the display device to which OpenGL is not syncing. You can use the environment variable __GL_SYNC_DISPLAY_DEVICE to specify to which display device OpenGL should sync. You should set this environment variable to the name of a display device; for example "CRT-1". Look for the line "Connected display device(s):" in your X log file for a list of the display devices present and their names. You may also find it useful to review Chapter 13 "Configuring Twinview" and the section on Ensuring Identical Mode Timings in Chapter 19. 11D. CONTROLLING THE SORTING OF OPENGL FBCONFIGS The NVIDIA GLX implementation sorts FBConfigs returned by glXChooseFBConfig() as described in the GLX specification. To disable this behavior set __GL_SORT_FBCONFIGS to 0 (zero), then FBConfigs will be returned in the order they were received from the X server. To examine the order in which FBConfigs are returned by the X server run: nvidia-settings --glxinfo This option may be be useful to work around problems in which applications pick an unexpected FBConfig. 11E. OPENGL YIELD BEHAVIOR There are several cases where the NVIDIA OpenGL driver needs to wait for external state to change before continuing. To avoid consuming too much CPU time in these cases, the driver will sometimes yield so the kernel can schedule other processes to run while the driver waits. For example, when waiting for free space in a command buffer, if the free space has not become available after a certain number of iterations, the driver will yield before it continues to loop. By default, the driver calls sched_yield() to do this. However, this can cause the calling process to be scheduled out for a relatively long period of time if there are other, same-priority processes competing for time on the CPU. One example of this is when an OpenGL-based composite manager is moving and repainting a window and the X server is trying to update the window as it moves, which are both CPU-intensive operations. You can use the __GL_YIELD environment variable to work around these scheduling problems. This variable allows the user to specify what the driver should do when it wants to yield. The possible values are: __GL_YIELD Behavior --------------- ------------------------------------------------------ By default, OpenGL will call sched_yield() to yield. "NOTHING" OpenGL will never yield. "USLEEP" OpenGL will call usleep(0) to yield. 11F. CONTROLLING WHICH OPENGL FBCONFIGS ARE AVAILABLE The NVIDIA GLX implementation will hide FBConfigs that are associated with a 32-bit ARGB visual when the XLIB_SKIP_ARGB_VISUALS environment variable is defined. This matches the behavior of libX11, which will hide those visuals from XGetVisualInfo and XMatchVisualInfo. This environment variable is useful when applications are confused by the presence of these FBConfigs. 11G. USING UNOFFICIAL GLX PROTOCOL By default, the NVIDIA GLX implementation will not expose GLX protocol for GL commands if the protocol is not considered complete. Protocol could be considered incomplete for a number of reasons. The implementation could still be under development and contain known bugs, or the protocol specification itself could be under development or going through review. If users would like to test the client-side portion of such protocol when using indirect rendering, they can set the __GL_ALLOW_UNOFFICIAL_PROTOCOL environment variable to a non-zero value before starting their GLX application. When an NVIDIA GLX server is used, the related X Config option "AllowUnofficialGLXProtocol" will need to be set as well to enable support in the server. ______________________________________________________________________________ Chapter 12. Configuring AGP ______________________________________________________________________________ There are several choices for configuring the NVIDIA kernel module's use of AGP on Linux. You can choose to either use the NVIDIA builtin AGP driver (NvAGP), or the AGP driver that comes with the Linux kernel (AGPGART). This is controlled through the "NvAGP" option in your X config file: Option "NvAGP" "0" ... disables AGP support Option "NvAGP" "1" ... use NvAGP, if possible Option "NvAGP" "2" ... use AGPGART, if possible Option "NvAGP" "3" ... try AGPGART; if that fails, try NvAGP The default is 3 (the default was 1 until after 1.0-1251). You should use the AGP driver that works best with your AGP chipset. If you are experiencing problems with stability, you may want to start by disabling AGP and seeing if that solves the problems. Then you can experiment with the AGP driver configuration. You can query the current AGP status at any time via the '/proc' filesystem interface (see Chapter 21). To use the Linux 2.4 AGPGART driver, you will need to compile it with your kernel and either statically link it in, or build it as a module and load it. To use the Linux 2.6 AGPGART driver, both the AGPGART frontend module, 'apggart.ko', and the backend module for your AGP chipset ('nvidia-agp.ko', 'intel-agp.ko', 'via-agp.ko', ...) need to be statically linked into the kernel, or built as modules and loaded. NVIDIA builtin AGP support is unavailable if an AGPGART backend driver is loaded into the kernel. On Linux 2.4, it is recommended that you compile AGPGART as a module and make sure that it is not loaded when trying to use the NVIDIA AGP driver. On Linux 2.6, the 'agpgart.ko' frontend module will always be loaded, as it is used by the NVIDIA kernel module to determine if an AGPGART backend module is loaded. When the NVIDIA AGP driver is to be used on a Linux 2.6 system, it is recommended that you make sure the AGPGART backend drivers are built as modules and that they are not loaded. Also note that changing AGP drivers generally requires a reboot before the changes actually take effect. If you are using a recent Linux 2.6 kernel that has the Linux AGPGART driver statically linked in (some distribution kernels do), you can pass the agp=off parameter to the kernel (via LILO or GRUB, for example) to disable AGPGART support. As of Linux 2.6.11, most AGPGART backend drivers should respect this parameter. The following AGP chipsets are supported by the NVIDIA AGP driver; for all other chipsets it is recommended that you use the AGPGART module. Supported AGP Chipsets ---------------------------------------------------------------------- Intel 440LX Intel 440BX Intel 440GX Intel 815 ("Solano") Intel 820 ("Camino") Intel 830M Intel 840 ("Carmel") Intel 845 ("Brookdale") Intel 845G Intel 850 ("Tehama") Intel 855 ("Odem") Intel 860 ("Colusa") Intel 865G ("Springdale") Intel 875P ("Canterwood") Intel E7205 ("Granite Bay") Intel E7505 ("Placer") AMD 751 ("Irongate") AMD 761 ("IGD4") AMD 762 ("IGD4 MP") AMD 8151 ("Lokar") VIA 8371 VIA 82C694X VIA KT133 VIA KT266 VIA KT400 VIA P4M266 VIA P4M266A VIA P4X400 VIA K8T800 VIA K8N800 VIA PT880 VIA KT880 RCC CNB20LE RCC 6585HE Micron SAMDDR ("Samurai") Micron SCIDDR ("Scimitar") NVIDIA nForce NVIDIA nForce2 NVIDIA nForce3 ALi 1621 ALi 1631 ALi 1647 ALi 1651 ALi 1671 SiS 630 SiS 633 SiS 635 SiS 645 SiS 646 SiS 648 SiS 648FX SiS 650 SiS 651 SiS 655 SiS 655FX SiS 661 SiS 730 SiS 733 SiS 735 SiS 745 SiS 755 ATI RS200M If you are experiencing AGP stability problems, you should be aware of the following: Additional AGP Information Support for the processor's Page Size Extension on Athlon Processors Some Linux kernels have a conflicting cache attribute bug that is exposed by advanced speculative caching in newer AMD Athlon family processors (AMD Athlon XP, AMD Athlon 4, AMD Athlon MP, and Models 6 and above AMD Duron). This kernel bug usually shows up under heavy use of accelerated 3D graphics with an AGP graphics card. Linux distributions based on kernel 2.4.19 and later *should* incorporate the bug fix, but older kernels require help from the user in ensuring that a small portion of advanced speculative caching is disabled (normally done through a kernel patch) and a boot option is specified in order to apply the whole fix. NVIDIA's driver automatically disables the small portion of advanced speculative caching for the affected AMD processors without the need to patch the kernel; it can be used even on kernels which do already incorporate the kernel bug fix. Additionally, for older kernels the user performs the boot option portion of the fix by explicitly disabling 4MB pages. This can be done from the boot command line by specifying: mem=nopentium Or by adding the following line to /etc/lilo.conf: append = "mem=nopentium" AGP Rate You may want to decrease the AGP rate setting if you are seeing lockups with the value you are currently using. You can do so by extracting the '.run' file: # sh NVIDIA-Linux-x86-256.29.run --extract-only # cd NVIDIA-Linux-x86-256.29/kernel/ Then edit nv-reg.h, and make the following changes: - NV_DEFINE_REG_ENTRY(__NV_REQ_AGP_RATE, 15); + NV_DEFINE_REG_ENTRY(__NV_REQ_AGP_RATE, 4); /* force AGP Rate to 4x */ or + NV_DEFINE_REG_ENTRY(__NV_REQ_AGP_RATE, 2); /* force AGP Rate to 2x */ or + NV_DEFINE_REG_ENTRY(__NV_REQ_AGP_RATE, 1); /* force AGP Rate to 1x */ Then recompile and load the new kernel module. To do this, run 'nvidia-installer' with the -n command line option: # cd ../../..; ./nvidia-installer -n AGP drive strength BIOS setting (Via-based motherboards) Many Via-based motherboards allow adjusting the AGP drive strength in the system BIOS. The setting of this option largely affects system stability, the range between 0xEA and 0xEE seems to work best for NVIDIA hardware. Setting either nibble to 0xF generally results in severe stability problems. If you decide to experiment with this, you need to be aware of the fact that you are doing so at your own risk and that you may render your system unbootable with improper settings until you reset the setting to a working value (w/ a PCI graphics card or by resetting the BIOS to its default values). System BIOS version Make sure you have the latest system BIOS provided by the motherboard manufacturer. On ALi1541 and ALi1647 chipsets, NVIDIA drivers disable AGP to work around timing and signal integrity problems. You can force AGP to be enabled on these chipsets by setting NVreg_EnableALiAGP to 1. Note that this may cause the system to become unstable. Early system BIOS revisions for the ASUS A7V8X-X KT400 motherboard misconfigure the chipset when an AGP 2.x graphics card is installed; if X hangs on your ASUS KT400 system with either Linux AGPGART or NvAGP enabled and the installed graphics card is not an AGP 8x device, make sure that you have the latest system BIOS installed. ______________________________________________________________________________ Chapter 13. Configuring TwinView ______________________________________________________________________________ TwinView is a mode of operation where two display devices (digital flat panels, CRTs, and TVs) can display the contents of a single X screen in any arbitrary configuration. This method of multiple monitor use has several distinct advantages over other techniques (such as Xinerama): o A single X screen is used. The NVIDIA driver conceals all information about multiple display devices from the X server; as far as X is concerned, there is only one screen. o Both display devices share one frame buffer. Thus, all the functionality present on a single display (e.g., accelerated OpenGL) is available with TwinView. o No additional overhead is needed to emulate having a single desktop. If you are interested in using each display device as a separate X screen, see Chapter 15. 13A. X CONFIG TWINVIEW OPTIONS To enable TwinView, you must specify the following option in the Device section of your X Config file: Option "TwinView" You may also use any of the following options, though they are not required: Option "MetaModes" "" Option "SecondMonitorHorizSync" "" Option "SecondMonitorVertRefresh" "" Option "HorizSync" "" Option "VertRefresh" "" Option "TwinViewOrientation" "" Option "ConnectedMonitor" "" See detailed descriptions of each option below. Alternatively, you can enable TwinView by running nvidia-xconfig --twinview and restarting your X server. Or, you can configure TwinView dynamically in the "Display Configuration" page in nvidia-settings. 13B. DETAILED DESCRIPTION OF OPTIONS TwinView This option is required to enable TwinView; without it, all other TwinView related options are ignored. SecondMonitorHorizSync SecondMonitorVertRefresh You specify the constraints of the second monitor through these options. The values given should follow the same convention as the "HorizSync" and "VertRefresh" entries in the Monitor section. As the XF86Config man page explains it: the ranges may be a comma separated list of distinct values and/or ranges of values, where a range is given by two distinct values separated by a dash. The HorizSync is given in kHz, and the VertRefresh is given in Hz. These options are normally not needed: by default, the NVIDIA X driver retrieves the valid frequency ranges from the display device's EDID (see Appendix B for a description of the "UseEdidFreqs" option). The SecondMonitor options will override any frequency ranges retrieved from the EDID. HorizSync VertRefresh Which display device is "first" and which is "second" is often unclear. For this reason, you may use these options instead of the SecondMonitor versions. With these options, you can specify a semicolon-separated list of frequency ranges, each optionally prepended with a display device name. In addition, if SLI Mosaic mode is enabled, a GPU specifier can be used. For example: Option "HorizSync" "CRT-0: 50-110; DFP-0: 40-70" Option "VertRefresh" "CRT-0: 60-120; GPU-0.DFP-0: 60" See Appendix C on Display Device Names for more information. These options are normally not needed: by default, the NVIDIA X driver retrieves the valid frequency ranges from the display device's EDID (see Appendix B for a description of the "UseEdidFreqs" option). The "HorizSync" and "VertRefresh" options override any frequency ranges retrieved from the EDID or any frequency ranges specified with the "SecondMonitorHorizSync" and "SecondMonitorVertRefresh" options. MetaModes MetaModes are "containers" that store information about what mode should be used on each display device at any given time. Even if only one display device is actively in use, the NVIDIA X driver always uses a MetaMode to encapsulate the mode information per display device, so that it can support dynamically enabling TwinView. Multiple MetaModes list the combinations of modes and the sequence in which they should be used. When the NVIDIA driver tells X what modes are available, it is really the minimal bounding box of the MetaMode that is communicated to X, while the "per display device" mode is kept internal to the NVIDIA driver. In MetaMode syntax, modes within a MetaMode are comma separated, and multiple MetaModes are separated by semicolons. For example: ", ; , " Where is the name of the mode to be used on display device 0 concurrently with used on display device 1. A mode switch will then cause to be used on display device 0 and to be used on display device 1. Here is an example MetaMode: Option "MetaModes" "1280x1024,1280x1024; 1024x768,1024x768" If you want a display device to not be active for a certain MetaMode, you can use the mode name "NULL", or simply omit the mode name entirely: "1600x1200, NULL; NULL, 1024x768" or "1600x1200; , 1024x768" Optionally, mode names can be followed by offset information to control the positioning of the display devices within the virtual screen space; e.g., "1600x1200 +0+0, 1024x768 +1600+0; ..." Offset descriptions follow the conventions used in the X "-geometry" command line option; i.e., both positive and negative offsets are valid, though negative offsets are only allowed when a virtual screen size is explicitly given in the X config file. When no offsets are given for a MetaMode, the offsets will be computed following the value of the TwinViewOrientation option (see below). Note that if offsets are given for any one of the modes in a single MetaMode, then offsets will be expected for all modes within that single MetaMode; in such a case offsets will be assumed to be +0+0 when not given. When not explicitly given, the virtual screen size will be computed as the the bounding box of all MetaMode bounding boxes. MetaModes with a bounding box larger than an explicitly given virtual screen size will be discarded. A MetaMode string can be further modified with a "Panning Domain" specification; e.g., "1024x768 @1600x1200, 800x600 @1600x1200" A panning domain is the area in which a display device's viewport will be panned to follow the mouse. Panning actually happens on two levels with TwinView: first, an individual display device's viewport will be panned within its panning domain, as long as the viewport is contained by the bounding box of the MetaMode. Once the mouse leaves the bounding box of the MetaMode, the entire MetaMode (i.e., all display devices) will be panned to follow the mouse within the virtual screen, unless the "PanAllDisplays" X configuration option is disabled. Note that individual display devices' panning domains default to being clamped to the position of the display devices' viewports, thus the default behavior is just that viewports remain "locked" together and only perform the second type of panning. The most beneficial use of panning domains is probably to eliminate dead areas -- regions of the virtual screen that are inaccessible due to display devices with different resolutions. For example: "1600x1200, 1024x768" produces an inaccessible region below the 1024x768 display. Specifying a panning domain for the second display device: "1600x1200, 1024x768 @1024x1200" provides access to that dead area by allowing you to pan the 1024x768 viewport up and down in the 1024x1200 panning domain. Offsets can be used in conjunction with panning domains to position the panning domains in the virtual screen space (note that the offset describes the panning domain, and only affects the viewport in that the viewport must be contained within the panning domain). For example, the following describes two modes, each with a panning domain width of 1900 pixels, and the second display is positioned below the first: "1600x1200 @1900x1200 +0+0, 1024x768 @1900x768 +0+1200" Because it is often unclear which mode within a MetaMode will be used on each display device, mode descriptions within a MetaMode can be prepended with a display device name. For example: "CRT-0: 1600x1200, DFP-0: 1024x768" If no MetaMode string is specified, then the X driver uses the modes listed in the relevant "Display" subsection, attempting to place matching modes on each display device. TwinViewOrientation This option controls the positioning of the second display device relative to the first within the virtual X screen, when offsets are not explicitly given in the MetaModes. The possible values are: "RightOf" (the default) "LeftOf" "Above" "Below" "Clone" When "Clone" is specified, both display devices will be assigned an offset of 0,0. Because it is often unclear which display device is "first" and which is "second", TwinViewOrientation can be confusing. You can further clarify the TwinViewOrientation with display device names to indicate which display device is positioned relative to which display device. For example: "CRT-0 LeftOf DFP-0" ConnectedMonitor With this option you can override what the NVIDIA kernel module detects is connected to your graphics card. This may be useful, for example, if any of your display devices do not support detection using Display Data Channel (DDC) protocols. Valid values are a comma-separated list of display device names; for example: "CRT-0, CRT-1" "CRT" "CRT-1, DFP-0" WARNING: this option overrides what display devices are detected by the NVIDIA kernel module, and is very seldom needed. You really only need this if a display device is not detected, either because it does not provide DDC information, or because it is on the other side of a KVM (Keyboard-Video-Mouse) switch. In most other cases, it is best not to specify this option. Just as in all X config entries, spaces are ignored and all entries are case insensitive. 13C. DYNAMIC TWINVIEW Using the NV-CONTROL X extension, the display devices in use by an X screen, the mode pool for each display device, and the MetaModes for each X screen can be dynamically manipulated. The "Display Configuration" page in nvidia-settings uses this functionality to modify the MetaMode list and then uses XRandR to switch between MetaModes. This gives the ability to dynamically configure TwinView. The details of how this works are documented in the nv-control-dpy.c sample NV-CONTROL client in the nvidia-settings source tarball. Because the NVIDIA X driver can now transition into and out of TwinView dynamically, MetaModes are always used internally by the NVIDIA X driver, regardless of how many display devices are currently in use by the X screen and regardless of whether the TwinView X configuration option was specified. One implication of this implementation is that each MetaMode must be uniquely identifiable to the XRandR X extension. Unfortunately, two MetaModes with the same bounding box will look the same to XRandR. For example, two MetaModes with different orientations: "CRT: 1600x1200 +0+0, DFP: 1600x1200 +1600+0" "CRT: 1600x1200 +1600+0, DFP: 1600x1200 +0+0" will look identical to the XRandR or XF86VidMode X extensions, because they have the same total size (3200x1200), and nvidia-settings would not be able to use XRandR to switch between these MetaModes. To work around this limitation, the NVIDIA X driver "lies" about the refresh rate of each MetaMode, using the refresh rate of the MetaMode as a unique identifier. The XRandR extension is currently being redesigned by the X.Org community, so the refresh rate workaround may be removed at some point in the future. This workaround can also be disabled by setting the "DynamicTwinView" X configuration option to FALSE, which will disable NV-CONTROL support for manipulating MetaModes, but will cause the XRandR and XF86VidMode visible refresh rate to be accurate. FREQUENTLY ASKED TWINVIEW QUESTIONS Q. Nothing gets displayed on my second monitor; what is wrong? A. Monitors that do not support monitor detection using Display Data Channel (DDC) protocols (this includes most older monitors) are not detectable by your NVIDIA card. You need to explicitly tell the NVIDIA X driver what you have connected using the "ConnectedMonitor" option; e.g., Option "ConnectedMonitor" "CRT, CRT" Q. Will window managers be able to appropriately place windows (e.g., avoiding placing windows across both display devices, or in inaccessible regions of the virtual desktop)? A. Yes. The NVIDIA X driver provides a Xinerama extension that X clients (such as window managers) can use to discover the current TwinView configuration. Note that the Xinerama protocol provides no way to notify clients when a configuration change occurs, so if you modeswitch to a different MetaMode, your window manager will still think you have the previous configuration. Using the Xinerama extension, in conjunction with the XF86VidMode extension to get modeswitch events, window managers should be able to determine the TwinView configuration at any given time. Unfortunately, the data provided by XineramaQueryScreens() appears to confuse some window managers; to work around such broken window mangers, you can disable communication of the TwinView screen layout with the "NoTwinViewXineramaInfo" X config Option (see Appendix B for details). The order that display devices are reported in via the TwinView Xinerama information can be configured with the TwinViewXineramaInfoOrder X configuration option. Be aware that the NVIDIA driver cannot provide the Xinerama extension if the X server's own Xinerama extension is being used. Explicitly specifying Xinerama in the X config file or on the X server commandline will prohibit NVIDIA's Xinerama extension from installing, so make sure that the X server's log file does not contain: (++) Xinerama: enabled if you want the NVIDIA driver to be able to provide the Xinerama extension while in TwinView. Another solution is to use panning domains to eliminate inaccessible regions of the virtual screen (see the MetaMode description above). A third solution is to use two separate X screens, rather than use TwinView. See Chapter 15. Q. Why can I not get a resolution of 1600x1200 on the second display device when using a GeForce2 MX? A. Because the second display device on the GeForce2 MX was designed to be a digital flat panel, the Pixel Clock for the second display device is only 150 MHz. This effectively limits the resolution on the second display device to somewhere around 1280x1024 (for a description of how Pixel Clock frequencies limit the programmable modes, see the XFree86 Video Timings HOWTO). This constraint is not present on GeForce4 or GeForce FX GPUs -- the maximum pixel clock is the same on both heads. Q. Do video overlays work across both display devices? A. Hardware video overlays only work on the first display device. The current solution is that blitted video is used instead on TwinView. Q. How are virtual screen dimensions determined in TwinView? A. After all requested modes have been validated, and the offsets for each MetaMode's viewports have been computed, the NVIDIA driver computes the bounding box of the panning domains for each MetaMode. The maximum bounding box width and height is then found. Note that one side effect of this is that the virtual width and virtual height may come from different MetaModes. Given the following MetaMode string: "1600x1200,NULL; 1024x768+0+0, 1024x768+0+768" the resulting virtual screen size will be 1600 x 1536. Q. Can I play full screen games across both display devices? A. Yes. While the details of configuration will vary from game to game, the basic idea is that a MetaMode presents X with a mode whose resolution is the bounding box of the viewports for that MetaMode. For example, the following: Option "MetaModes" "1024x768,1024x768; 800x600,800x600" Option "TwinViewOrientation" "RightOf" produce two modes: one whose resolution is 2048x768, and another whose resolution is 1600x600. Games such as Quake 3 Arena use the VidMode extension to discover the resolutions of the modes currently available. To configure Quake 3 Arena to use the above MetaMode string, add the following to your q3config.cfg file: seta r_customaspect "1" seta r_customheight "600" seta r_customwidth "1600" seta r_fullscreen "1" seta r_mode "-1" Note that, given the above configuration, there is no mode with a resolution of 800x600 (remember that the MetaMode "800x600, 800x600" has a resolution of 1600x600"), so if you change Quake 3 Arena to use a resolution of 800x600, it will display in the lower left corner of your screen, with the rest of the screen grayed out. To have single head modes available as well, an appropriate MetaMode string might be something like: "800x600,800x600; 1024x768,NULL; 800x600,NULL; 640x480,NULL" More precise configuration information for specific games is beyond the scope of this document, but the above examples coupled with numerous online sources should be enough to point you in the right direction. ______________________________________________________________________________ Chapter 14. Configuring GLX in Xinerama ______________________________________________________________________________ The NVIDIA Linux Driver supports GLX when Xinerama is enabled on similar GPUs. The Xinerama extension takes multiple physical X screens (possibly spanning multiple GPUs), and binds them into one logical X screen. This allows windows to be dragged between GPUs and to span across multiple GPUs. The NVIDIA driver supports hardware accelerated OpenGL rendering across all NVIDIA GPUs when Xinerama is enabled. To configure Xinerama 1. Configure multiple X screens (refer to the XF86Config(5x) or xorg.conf(5x) man pages for details). 2. Enable Xinerama by adding the line Option "Xinerama" "True" to the "ServerFlags" section of your X config file. Requirements: o Using identical GPUs is recommended. Some combinations of non-identical, but similar, GPUs are supported. If a GPU is incompatible with the rest of a Xinerama desktop then no OpenGL rendering will appear on the screens driven by that GPU. Rendering will still appear normally on screens connected to other supported GPUs. In this situation the X log file will include a message of the form: (WW) NVIDIA(2): The GPU driving screen 2 is incompatible with the rest of (WW) NVIDIA(2): the GPUs composing the desktop. OpenGL rendering will (WW) NVIDIA(2): be disabled on screen 2. o NVIDIA's GLX implementation only supports Xinerama when physical X screen 0 is driven by the NVIDIA X driver. This is because the X.Org X server bases the visuals of the logical Xinerama X screen on the visuals of physical X screen 0. When physical X screen 0 is not being driven by the NVIDIA X driver and Xinerama is enabled, then GLX will be disabled. If physical X screens other than screen 0 are not being driven by the NVIDIA X driver, OpenGL rendering will be disabled on them. o Only the intersection of capabilities across all GPUs will be advertised. The maximum OpenGL viewport size depends on the hardware used, and is described by the following table. If an OpenGL window is larger than the maximum viewport, regions beyond the viewport will be blank. OpenGL Viewport Maximums in Xinerama GeForce GPUs before GeForce 8: 4096 x 4096 pixels GeForce 8 through GeForce GTX 8192 x 8192 pixels 400 GPUs: GeForce GTX 400 series GPUs: 16384x16384 pixels Quadro 5 series GPUs: as large as the Xinerama desktop o X configuration options that affect GLX operation (e.g.: stereo, overlays) should be set consistently across all X screens in the X server. Known Issues: o Versions of XFree86 prior to 4.5 and versions of X.Org prior to 6.8.0 lack the required interfaces to properly implement overlays with the Xinerama extension. On earlier server versions mixing overlays and Xinerama will result in rendering corruption. If you are using the Xinerama extension with overlays, it is recommended that you upgrade to XFree86 4.5, X.Org 6.8.0, or newer. ______________________________________________________________________________ Chapter 15. Configuring Multiple X Screens on One Card ______________________________________________________________________________ GPUs that support TwinView (Chapter 13) can also be configured to treat each connected display device as a separate X screen. While there are several disadvantages to this approach as compared to TwinView (e.g.: windows cannot be dragged between X screens, hardware accelerated OpenGL cannot span the two X screens), it does offer several advantages over TwinView: o If each display device is a separate X screen, then properties that may vary between X screens may vary between displays (e.g.: depth, root window size, etc). o Hardware that can only be used on one display at a time (e.g.: video overlays, hardware accelerated RGB overlays), and which consequently cannot be used at all when in TwinView, can be exposed on the first X screen when each display is a separate X screen. o TwinView is a fairly new feature. X has historically used one screen per display device. To configure two separate X screens to share one graphics card, here is what you will need to do: First, create two separate Device sections, each listing the BusID of the graphics card to be shared and listing the driver as "nvidia", and assign each a separate screen: Section "Device" Identifier "nvidia0" Driver "nvidia" # Edit the BusID with the location of your graphics card BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "nvidia1" Driver "nvidia" # Edit the BusID with the location of your graphics card BusId "PCI:2:0:0" Screen 1 EndSection Then, create two Screen sections, each using one of the Device sections: Section "Screen" Identifier "Screen0" Device "nvidia0" Monitor "Monitor0" DefaultDepth 24 Subsection "Display" Depth 24 Modes "1600x1200" "1024x768" "800x600" "640x480" EndSubsection EndSection Section "Screen" Identifier "Screen1" Device "nvidia1" Monitor "Monitor1" DefaultDepth 24 Subsection "Display" Depth 24 Modes "1600x1200" "1024x768" "800x600" "640x480" EndSubsection EndSection (Note: You'll also need to create a second Monitor section) Finally, update the ServerLayout section to use and position both Screen sections: Section "ServerLayout" ... Screen 0 "Screen0" Screen 1 "Screen1" leftOf "Screen0" ... EndSection For further details, refer to the XF86Config(5x) or xorg.conf(5x) man pages. ______________________________________________________________________________ Chapter 16. Configuring TV-Out ______________________________________________________________________________ NVIDIA GPU-based graphics cards with a TV-Out connector can use a television as another display device (the same way that it would use a CRT or digital flat panel). The TV can be used by itself, or in conjunction with another display device in a TwinView or multiple X screen configuration. If a TV is the only display device connected to your graphics card, it will be used as the primary display when you boot your system (i.e. the console will come up on the TV just as if it were a CRT). The NVIDIA X driver populates the mode pool for the TV with all the mode sizes that the driver supports with the given TV standard and the TV encoder on the graphics card. These modes are given names that correspond to their resolution; e.g., "800x600". Because these TV modes only depend on the TV encoder and the TV standard, TV modes do not go through normal mode validation. The X configuration options HorizSync and VertRefresh are not used for TV mode validation. Additionally, the NVIDIA driver contains a hardcoded list of mode sizes that it can drive for each combination of TV encoder and TV standard. Therefore, custom modelines in your X configuration file are ignored for TVs. To use your TV with X, there are several relevant X configuration options: o The Modes in the screen section of your X configuration file; you can use these to request any of the modes in the mode pool which the X driver created for this combination of TV standard and TV encoder. Examples include "640x480" and "800x600". If in doubt, use "nvidia-auto-select". o The "TVStandard" option should be added to your screen section; valid values are: TVStandard Description ------------- -------------------------------------------------- "PAL-B" used in Belgium, Denmark, Finland, Germany, Guinea, Hong Kong, India, Indonesia, Italy, Malaysia, The Netherlands, Norway, Portugal, Singapore, Spain, Sweden, and Switzerland "PAL-D" used in China and North Korea "PAL-G" used in Denmark, Finland, Germany, Italy, Malaysia, The Netherlands, Norway, Portugal, Spain, Sweden, and Switzerland "PAL-H" used in Belgium "PAL-I" used in Hong Kong and The United Kingdom "PAL-K1" used in Guinea "PAL-M" used in Brazil "PAL-N" used in France, Paraguay, and Uruguay "PAL-NC" used in Argentina "NTSC-J" used in Japan "NTSC-M" used in Canada, Chile, Colombia, Costa Rica, Ecuador, Haiti, Honduras, Mexico, Panama, Puerto Rico, South Korea, Taiwan, United States of America, and Venezuela "HD480i" 480 line interlaced "HD480p" 480 line progressive "HD720p" 720 line progressive "HD1080i" 1080 line interlaced "HD1080p" 1080 line progressive "HD576i" 576 line interlace "HD576p" 576 line progressive The line in your X config file should be something like: Option "TVStandard" "NTSC-M" If you do not specify a TVStandard, or you specify an invalid value, the default "NTSC-M" will be used. Note: if your country is not in the above list, select the country closest to your location. o The "UseDisplayDevice" option can be used if there are multiple display devices connected, and you want the connected TV to be used instead of the connected CRTs and/or DFPs. E.g., Option "UseDisplayDevice" "TV" Using the "UseDisplayDevice" option, rather than the "ConnectedMonitor" option, is recommended. o The "TVOutFormat" option can be used to force the output format. Without this option, the driver autodetects the output format. Unfortunately, it does not always do this correctly. The output format can be forced with the "TVOutFormat" option; valid values are: TVOutFormat Description Supported TV standards ------------------- ------------------- ------------------- "AUTOSELECT" The driver PAL, NTSC, HD autodetects the output format (default value). "COMPOSITE" Force Composite PAL, NTSC output format "SVIDEO" Force S-Video PAL, NTSC output format "COMPONENT" Force Component HD output format, also called YPbPr "SCART" Force Scart output PAL, NTSC format, also called Peritel The line in your X config file should be something like: Option "TVOutFormat" "SVIDEO" o The "TVOverScan" option can be used to enable Overscan, when the TV encoder supports it. Valid values are decimal values in the range 1.0 (which means overscan as much as possible: make the image as large as possible) and 0.0 (which means disable overscanning: make the image as small as possible). Overscanning is disabled (0.0) by default. The NVIDIA X driver may not restore the console correctly with XFree86 versions older than 4.3 when the console is a TV. This is due to binary incompatibilities between XFree86 int10 modules. If you use a TV as your console it is recommended that you upgrade to XFree86 4.3 or later. ______________________________________________________________________________ Chapter 17. Using the XRandR Extension ______________________________________________________________________________ X.Org version X11R6.8.1 contains support for the rotation component of the XRandR extension, which allows screens to be rotated at 90 degree increments. The driver supports rotation with the extension when 'Option "RandRRotation"' is enabled in the X config file. Workstation RGB or CI overlay visuals will function at lower performance and the video overlay will not be available when RandRRotation is enabled. You can query the available rotations using the 'xrandr' command line interface to the RandR extension by running: xrandr -q You can set the rotation orientation of the screen by running any of: xrandr -o left xrandr -o right xrandr -o inverted xrandr -o normal Rotation may also be set through the nvidia-settings configuration utility in the "Rotation Settings" panel. SLI and rotation are incompatible. Rotation will be disabled when SLI is enabled. TwinView and rotation can be used together, but rotation affects the entire desktop. This means that the same rotation setting will apply to both display devices in a TwinView pair. Note also that the "TwinViewOrientation" option applies before rotation does. For example, if you have two screens side-by-side and you want to rotate them, you should set "TwinViewOrientation" to "Above" or "Below". ______________________________________________________________________________ Chapter 18. Configuring a Notebook ______________________________________________________________________________ 18A. INSTALLATION AND CONFIGURATION Installation and configuration of the NVIDIA Linux Driver Set on a notebook is the same as for any desktop environment, with a few additions, as described below. 18B. POWER MANAGEMENT All notebook NVIDIA GPUs support power management, both S3 (also known as "Standby" or "Suspend to RAM") and S4 (also known as "Hibernate", "Suspend to Disk" or "SWSUSP"). Power management is system-specific and is dependent upon all the components in the system; some systems may be more problematic than other systems. Most recent notebook NVIDIA GPUs also support PowerMizer, which monitors application work load to adjust system parameters to deliver the optimal balance of performance and battery life. However, PowerMizer is only enabled by default on some notebooks. Please see the known issues below for more details. 18C. HOTKEY SWITCHING OF DISPLAY DEVICES Mobile NVIDIA GPUs also have the capacity to react to a display change hotkey event, toggling between each of the connected display devices and each possible combination of the connected display devices (note that only 2 display devices may be active at a time). Hotkey switching dynamically changes the TwinView configuration; a given hotkey event will indicate which display devices should be in use at that time, and all MetaModes currently configured on the X screen will be updated to use the new configuration of display devices. Another important aspect of hotkey functionality is that you can dynamically connect and remove display devices to/from your notebook and use the hotkey to activate and deactivate them without restarting X. Note that there are two approaches to implementing this hotkey support: ACPI events and polling. Most recent notebooks use ACPI events to deliver hotkeys from the System BIOS to the graphics driver. This is the preferred method of delivering hotkey events, but is still a new feature under most UNIX platforms and may not always function correctly. The polling mechanism requires checking during the vertical blanking interval for a hotkey status change. It is an older mechanism for handling hotkeys, and is therefore not supported on all notebooks and is not tested by notebook manufacturers. It also does not always report the same combinations of display devices that are reported by ACPI hotkey events. The NVIDIA Linux Driver will attempt to use ACPI hotkey events, if possible. In the case that ACPI hotkey event support is not available, the driver will revert back to trying hotkey polling. In the case that the notebook does not support hotkey polling, hotkeys will not work. Please see the known issues section below for more details. When switching away from X to a virtual terminal, the VGA console will always be restored to the display device on which it was present when X was started. Similarly, when switching back into X, the same display device configuration will be used as when you switched away, regardless of what display change hotkey activity occurred while the virtual terminal was active. 18D. DOCKING EVENTS All notebook NVIDIA GPUs support docking, however support may be limited by the OS or system. There are three types of notebook docking (hot, warm, and cold), which refer to the state of the system when the docking event occurs. hot refers to a powered on system with a live desktop, warm refers to a system that has entered a suspended power management state, and cold refers to a system that has been powered off. Only warm and cold docking are supported by the NVIDIA driver. 18E. TWINVIEW All notebook NVIDIA GPUs support TwinView. TwinView on a notebook can be configured in the same way as on a desktop computer (refer to Chapter 13 ); note that in a TwinView configuration using the notebook's internal flat panel and an external CRT, the CRT is the primary display device (specify its HorizSync and VertRefresh in the Monitor section of your X config file) and the flat panel is the secondary display device (specify its HorizSync and VertRefresh through the SecondMonitorHorizSync and SecondMonitorVertRefresh options). The "UseEdidFreqs" X config option is enabled by default, so normally you should not need to specify the "SecondMonitorHorizSync" and "SecondMonitorVertRefresh" options. See the description of the UseEdidFreqs option in Appendix B for details). 18F. KNOWN NOTEBOOK ISSUES There are a few known issues associated with notebooks: o Display change hotkey switching is not available on all notebooks. In some cases, the ACPI infrastructure is not fully supported by the NVIDIA Linux Driver. Work is ongoing to increase the robustness of NVIDIA's support in this area. Toshiba and Lenovo notebooks are known to be problematic. o ACPI Display change hotkey switching is not supported by X.Org X servers earlier than 1.2.0; see EnableACPIHotkeys in Appendix B for details. o In many cases, suspending and/or resuming will fail. As mentioned above, this functionality is very system-specific. There are still many cases that are problematic. Here are some tips that may help: o In some cases, hibernation can have bad interactions with the PCI Express bus clocks, which can lead to system hangs when entering hibernation. This issue is still being investigated, but a known workaround is to leave an OpenGL application running when hibernating. o On notebooks with relatively little system memory, repetitive hibernation attempts may fail due to insufficient free memory. This problem can be avoided by running `echo 0 > /sys/power/image_size`, which reduces the image size to be stored during hibernation. o Some distributions use a tool called vbetool to save and restore VGA adapter state. This tool is incompatible with NVIDIA GPUs' Video BIOSes and is likely to lead to problems restoring the GPU and its state. Disabling calls to this tool in your distribution's init scripts may improve power management reliability. o On some notebooks, PowerMizer is not enabled by default. This issue is being investigated, and there is no known workaround. o The video overlay only works on the first display device on which you started X. For example, if you start X on the internal LCD, run a video application that uses the video overlay (uses the "Video Overlay" adapter advertised through the XV extension), and then hotkey switch to add a second display device, the video will not appear on the second display device. To work around this, you can either configure the video application to use the "Video Blitter" adapter advertised through the XV extension (this is always available), or hotkey switch to the display device on which you want to use the video overlay *before* starting X. ______________________________________________________________________________ Chapter 19. Programming Modes ______________________________________________________________________________ The NVIDIA Accelerated Linux Graphics Driver supports all standard VGA and VESA modes, as well as most user-written custom mode lines; double-scan modes are supported on all hardware. Interlaced modes are supported on all GeForce FX/Quadro FX and newer GPUs, and certain older GPUs; the X log file will contain a message "Interlaced video modes are supported on this GPU" if interlaced modes are supported. To request one or more standard modes for use in X, you can simply add a "Modes" line such as: Modes "1600x1200" "1024x768" "640x480" in the appropriate Display subsection of your X config file (see the XF86Config(5x) or xorg.conf(5x) man pages for details). Or, the nvidia-xconfig(1) utility can be used to request additional modes; for example: nvidia-xconfig --mode 1600x1200 See the nvidia-xconfig(1) man page for details. 19A. DEPTH, BITS PER PIXEL, AND PITCH While not directly a concern when programming modes, the bits used per pixel is an issue when considering the maximum programmable resolution; for this reason, it is worthwhile to address the confusion surrounding the terms "depth" and "bits per pixel". Depth is how many bits of data are stored per pixel. Supported depths are 8, 15, 16, and 24. Most video hardware, however, stores pixel data in sizes of 8, 16, or 32 bits; this is the amount of memory allocated per pixel. When you specify your depth, X selects the bits per pixel (bpp) size in which to store the data. Below is a table of what bpp is used for each possible depth: Depth BPP ---------------------------------- ---------------------------------- 8 8 15 16 16 16 24 32 Lastly, the "pitch" is how many bytes in the linear frame buffer there are between one pixel's data, and the data of the pixel immediately below. You can think of this as the horizontal resolution multiplied by the bytes per pixel (bits per pixel divided by 8). In practice, the pitch may be more than this product due to alignment constraints. 19B. MAXIMUM RESOLUTIONS The NVIDIA Accelerated Linux Graphics Driver and NVIDIA GPU-based graphics cards support resolutions up to 16384x16384 pixels for the GeForce GTX 400 series and newer GPUs, 8192x8192 pixels for the GeForce 8 series and above, and up to 4096x4096 pixels for the GeForce 7 series and below, though the maximum resolution your system can support is also limited by the amount of video memory (see USEFUL FORMULAS for details) and the maximum supported resolution of your display device (monitor/flat panel/television). Also note that while use of a video overlay does not limit the maximum resolution or refresh rate, video memory bandwidth used by a programmed mode does affect the overlay quality. 19C. USEFUL FORMULAS The maximum resolution is a function both of the amount of video memory and the bits per pixel you elect to use: HR * VR * (bpp/8) = Video Memory Used In other words, the amount of video memory used is equal to the horizontal resolution (HR) multiplied by the vertical resolution (VR) multiplied by the bytes per pixel (bits per pixel divided by eight). Technically, the video memory used is actually the pitch times the vertical resolution, and the pitch may be slightly greater than (HR * (bpp/8)) to accommodate the hardware requirement that the pitch be a multiple of some value. Note that this is just memory usage for the frame buffer; video memory is also used by other things, such as OpenGL and pixmap caching. Another important relationship is that between the resolution, the pixel clock (also known as the dot clock) and the vertical refresh rate: RR = PCLK / (HFL * VFL) In other words, the refresh rate (RR) is equal to the pixel clock (PCLK) divided by the total number of pixels: the horizontal frame length (HFL) multiplied by the vertical frame length (VFL) (note that these are the frame lengths, and not just the visible resolutions). As described in the XFree86 Video Timings HOWTO, the above formula can be rewritten as: PCLK = RR * HFL * VFL Given a maximum pixel clock, you can adjust the RR, HFL and VFL as desired, as long as the product of the three is consistent. The pixel clock is reported in the log file. Your X log should contain a line like this: (--) NVIDIA(0): ViewSonic VPD150 (DFP-1): 165 MHz maximum pixel clock which indicates the maximum pixel clock for that display device. 19D. HOW MODES ARE VALIDATED In traditional XFree86/X.Org mode validation, the X server takes as a starting point the X server's internal list of VESA standard modes, plus any modes specified with special ModeLines in the X configuration file's Monitor section. These modes are validated against criteria such as the valid HorizSync/VertRefresh frequency ranges for the user's monitor (as specified in the Monitor section of the X configuration file), as well as the maximum pixel clock of the GPU. Once the X server has determined the set of valid modes, it takes the list of user requested modes (i.e., the set of modes named in the "Modes" line in the Display subsection of the Screen section of X configuration file), and finds the "best" validated mode with the requested name. The NVIDIA X driver uses a variation on the above approach to perform mode validation. During X server initialization, the NVIDIA X driver builds a pool of valid modes for each display device. It gathers all possible modes from several sources: o The display device's EDID o The X server's built-in list o Any user-specified ModeLines in the X configuration file o The VESA standard modes For every possible mode, the mode is run through mode validation. The core of mode validation is still performed similarly to traditional XFree86/X.Org mode validation: the mode timings are checked against things such as the valid HorizSync and VertRefresh ranges and the maximum pixelclock. Note that each individual stage of mode validation can be independently controlled through the "ModeValidation" X configuration option. Note that when validating interlaced mode timings, VertRefresh specifies the field rate, rather than the frame rate. For example, the following modeline has a vertical refresh rate of 87 Hz: # 1024x768i @ 87Hz (industry standard) ModeLine "1024x768" 44.9 1024 1032 1208 1264 768 768 776 817 +hsync +vsync Interlace Invalid modes are discarded; valid modes are inserted into the mode pool. See MODE VALIDATION REPORTING for how to get more details on mode validation results for each considered mode. Valid modes are given a unique name that is guaranteed to be unique across the whole mode pool for this display device. This mode name is constructed approximately like this: x_ (e.g., "1600x1200_85") The name may also be prepended with another number to ensure the mode is unique; e.g., "1600x1200_85_0". As validated modes are inserted into the mode pool, duplicate modes are removed, and the mode pool is sorted, such that the "best" modes are at the beginning of the mode pool. The sorting is based roughly on: o Resolution o Source (EDID-provided modes are prioritized higher than VESA-provided modes, which are prioritized higher than modes that were in the X server's built-in list) o Refresh rate Once modes from all mode sources are validated and the mode pool is constructed, all modes with the same resolution are compared; the best mode with that resolution is added to the mode pool a second time, using just the resolution as its unique modename (e.g., "1600x1200"). In this way, when you request a mode using the traditional names (e.g., "1600x1200"), you still get what you got before (the 'best' 1600x1200 mode); the added benefit is that all modes in the mode pool can be addressed by a unique name. When verbose logging is enabled (see the FAQ section on increasing the amount of data printed in the X log file), the mode pool for each display device is printed to the X log file. After the mode pool is built for all display devices, the requested modes (as specified in the X configuration file), are looked up from the mode pool. Each requested mode that can be matched against a mode in the mode pool is then advertised to the X server and is available to the user through the X server's mode switching hotkeys (ctrl-alt-plus/minus) and the XRandR and XF86VidMode X extensions. If only one display device is in use by the X screen when the X server starts, all modes in the mode pool are implicitly made available to the X server. See the "IncludeImplicitMetaModes" X configuration option in Appendix B for details. 19E. THE NVIDIA-AUTO-SELECT MODE You can request a special mode by name in the X config file, named "nvidia-auto-select". When the X driver builds the mode pool for a display device, it selects one of the modes as the "nvidia-auto-select" mode; a new entry is made in the mode pool, and "nvidia-auto-select" is used as the unique name for the mode. The "nvidia-auto-select" mode is intended to be a reasonable mode for the display device in question. For example, the "nvidia-auto-select" mode is normally the native resolution for flat panels, as reported by the flat panel's EDID, or one of the detailed timings from the EDID. The "nvidia-auto-select" mode is guaranteed to always be present, and to always be defined as something considered valid by the X driver for this display device. Note that the "nvidia-auto-select" mode is not necessarily the largest possible resolution, nor is it necessarily the mode with the highest refresh rate. Rather, the "nvidia-auto-select" mode is selected such that it is a reasonable default. The selection process is roughly: o If the EDID for the display device reported a preferred mode timing, and that mode timing is considered a valid mode, then that mode is used as the "nvidia-auto-select" mode. You can check if the EDID reported a preferred timing by starting X with logverbosity greater than or equal to 5 (see the FAQ section on increasing the amount of data printed in the X log file), and looking at the EDID printout; if the EDID contains a line: Prefer first detailed timing : Yes Then the first mode listed under the "Detailed Timings" in the EDID will be used. o If the EDID did not provide a preferred timing, the best detailed timing from the EDID is used as the "nvidia-auto-select" mode. o If the EDID did not provide any detailed timings (or there was no EDID at all), the best valid mode not larger than 1024x768 is used as the "nvidia-auto-select" mode. The 1024x768 limit is imposed here to restrict use of modes that may have been validated, but may be too large to be considered a reasonable default, such as 2048x1536. o If all else fails, the X driver will use a built-in 800 x 600 60Hz mode as the "nvidia-auto-select" mode. If no modes are requested in the X configuration file, or none of the requested modes can be found in the mode pool, then the X driver falls back to the "nvidia-auto-select" mode, so that X can always start. Appropriate warning messages will be printed to the X log file in these fallback scenarios. You can add the "nvidia-auto-select" mode to your X configuration file by running the command nvidia-xconfig --mode nvidia-auto-select and restarting your X server. The X driver can generally do a much better job of selecting the "nvidia-auto-select" mode if the display device's EDID is available. This is one reason why it is recommended to only use the "UseEDID" X configuration option sparingly. Note that, rather than globally disable all uses of the EDID with the "UseEDID" option, you can individually disable each particular use of the EDID using the "UseEDIDFreqs", "UseEDIDDpi", and/or the "NoEDIDModes" argument in the "ModeValidation" X configuration option. 19F. MODE VALIDATION REPORTING When log verbosity is set to 6 or higher (see FAQ section on increasing the amount of data printed in the X log file), the X log will record every mode that is considered for each display device's mode pool, and report whether the mode passed or failed. For modes that were considered invalid, the log will report why the mode was considered invalid. 19G. ENSURING IDENTICAL MODE TIMINGS Some functionality, such as Active Stereo with TwinView, requires control over exactly which mode timings are used. For explicit control over which mode timings are used on each display device, you can specify the ModeLine you want to use (using one of the ModeLine generators available), and using a unique name. For example, if you wanted to use 1024x768 at 120 Hz on each monitor in TwinView with active stereo, you might add something like this to the monitor section of your X configuration file: # 1024x768 @ 120.00 Hz (GTF) hsync: 98.76 kHz; pclk: 139.05 MHz Modeline "1024x768_120" 139.05 1024 1104 1216 1408 768 769 772 823 -HSync +Vsync Then, in the Screen section of your X config file, specify a MetaMode like this: Option "MetaModes" "1024x768_120, 1024x768_120" 19H. ADDITIONAL INFORMATION An XFree86 ModeLine generator, conforming to the GTF Standard is available at http://gtf.sourceforge.net/. Additional generators can be found by searching for "modeline" on freshmeat.net. ______________________________________________________________________________ Chapter 20. Configuring Flipping and UBB ______________________________________________________________________________ The NVIDIA Accelerated Linux Graphics Driver supports Unified Back Buffer (UBB) and OpenGL Flipping. These features can provide performance gains in certain situations. o Unified Back Buffer (UBB): UBB is available only on the Quadro family of GPUs (Quadro4 NVS excluded) and is enabled by default when there is sufficient video memory available. This can be disabled with the UBB X config option described in Appendix B. When UBB is enabled, all windows share the same back, stencil and depth buffers. When there are many windows, the back, stencil and depth usage will never exceed the size of that used by a full screen window. However, even for a single small window, the back, stencil, and depth video memory usage is that of a full screen window. In that case video memory may be used less efficiently than in the non-UBB case. o Flipping: When OpenGL flipping is enabled, OpenGL can perform buffer swaps by changing which buffer the DAC scans out rather than copying the back buffer contents to the front buffer; this is generally a much higher performance mechanism and allows tearless swapping during the vertical retrace (when __GL_SYNC_TO_VBLANK is set). The conditions under which OpenGL can flip are slightly complicated, but in general: on GeForce or newer hardware, OpenGL can flip when a single full screen unobscured OpenGL application is running, and __GL_SYNC_TO_VBLANK is enabled. Additionally, OpenGL can flip on Quadro hardware even when an OpenGL window is partially obscured or not full screen or __GL_SYNC_TO_VBLANK is not enabled. ______________________________________________________________________________ Chapter 21. Using the Proc Filesystem Interface ______________________________________________________________________________ You can use the /proc filesystem interface to obtain run-time information about the driver, any installed NVIDIA graphics cards, and the AGP status. This information is contained in several files in /proc/driver/nvidia /proc/driver/nvidia/version Lists the installed driver revision and the version of the GNU C compiler used to build the Linux kernel module. /proc/driver/nvidia/warnings The NVIDIA graphics driver tries to detect potential problems with the host system's kernel and warns about them using the kernel's printk() mechanism, typically logged by the system to '/var/log/messages'. Important NVIDIA warning messages are also logged to dedicated text files in this /proc directory. /proc/driver/nvidia/cards/0...3 Provide information about each of the installed NVIDIA graphics adapters (model name, IRQ, BIOS version, Bus Type). Note that the BIOS version is only available while X is running. /proc/driver/nvidia/agp/card Information about the installed AGP card's AGP capabilities. /proc/driver/nvidia/agp/host-bridge Information about the host bridge (model and AGP capabilities). /proc/driver/nvidia/agp/status The current AGP status. If AGP support has been enabled on your system, the AGP driver being used, the AGP rate, and information about the status of AGP Fast Writes and Side Band Addressing is shown. The AGP driver is either NVIDIA (NVIDIA built-in AGP driver) or AGPGART (the Linux kernel's agpgart.o driver). If you see "inactive" next to AGPGART, then this means that the AGP chipset was programmed by AGPGART, but is not currently in use. SBA and Fast Writes indicate whether either one of these features is currently in use. Note that several factors determine whether support for either will be enabled. Even if both the AGP card and the host bridge support them, the driver may decide not to use these features in favor of system stability. This is particularly true of AGP Fast Writes. ______________________________________________________________________________ Chapter 22. Configuring Power Management Support ______________________________________________________________________________ The NVIDIA driver includes support for both APM- and ACPI- based power management. The NVIDIA Linux driver supports APM-based suspend and resume, as well as ACPI standby (S3) and suspend (S4). To use APM, your system's BIOS will need to support APM, rather than ACPI. Many, but not all, of the GeForce2- and GeForce4-based notebooks include APM support. You can check for APM support via the procfs interface (check for the existence of /proc/apm) or via the kernel's boot output: % dmesg | grep -i apm a message similar to this indicates APM support: apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) or a message like this indicates no APM support: No APM support in Kernel Note: If you are using Linux kernel 2.6 and your kernel was configured with support for both ACPI and APM, the NVIDIA kernel module will be built with ACPI Power Management support. If you wish to use APM, you will need to rebuild the Linux kernel without ACPI support and reinstall the NVIDIA Linux graphics driver. Sometimes chipsets lose their AGP configuration during suspend, and may cause corruption on the bus upon resume. The AGP driver is required to save and restore relevant register state on such systems; NVIDIA's NvAGP is notified of power management events and ensures its configuration is kept intact across suspend/resume cycles. Linux 2.4 AGPGART does not support power management, Linux 2.6 AGPGART does, but only for a few select chipsets. If you use either of these two AGP drivers and find your system fails to resume reliably, you may have more success with the NvAGP driver. Disabling AGP support (see Chapter 12 for more details on disabling AGP) will also work around this problem. More recent systems are more likely to support ACPI. ACPI is supported by the NVIDIA graphics driver in 2.6 and newer kernels. The driver supports ACPI standby (S3) and includes beta support for ACPI suspend (S4). If you enable ACPI S4 support via suspend2 patches, you will need to tweak the Linux kernel such that it dynamically determines the amount of pages needed by the drivers that will be suspended in the system. This is done by issuing the following command as root: % echo 0 > /sys/power/suspend2/extra_pages_allowance Older versions of suspend2 may provide a different interface, in which case the following command needs to be issued as root: % echo 0 > /proc/suspend2/extra_pages_allowance The system does NOT need rebooting, and as a matter of fact, the setting is volatile over reboots. You will need to include the tweak in your startup scripts. However, failure to perform the tweak will result in a hang going to sleep. For further information regarding suspend2 patches, see http://www.suspend2.net/. ______________________________________________________________________________ Chapter 23. Using the X Composite Extension ______________________________________________________________________________ X.Org X servers, beginning with X11R6.8.0, contain experimental support for a new X protocol extension called Composite. This extension allows windows to be drawn into pixmaps instead of directly onto the screen. In conjunction with the Damage and Render extensions, this allows a program called a composite manager to blend windows together to draw the screen. Performance will be degraded significantly if the "RenderAccel" option is disabled in xorg.conf. See Appendix B for more details. When the NVIDIA X driver is used with an X.Org X server X11R6.9.0 or newer and the Composite extension is enabled, NVIDIA's OpenGL implementation interacts properly with the Damage and Composite X extensions. This means that OpenGL rendering is drawn into offscreen pixmaps and the X server is notified of the Damage event when OpenGL renders to the pixmap. This allows OpenGL applications to behave properly in a composited X desktop. If the Composite extension is enabled on an X server older than X11R6.9.0, then GLX will be disabled. You can force GLX on while Composite is enabled on pre-X11R6.9.0 X servers with the "AllowGLXWithComposite" X configuration option. However, GLX will not render correctly in this environment. Upgrading your X server to X11R6.9.0 or newer is recommended. You can enable the Composite X extension by running 'nvidia-xconfig --composite'. Composite can be disabled with 'nvidia-xconfig --no-composite'. See the nvidia-xconfig(1) man page for details. If you are using Composite with GLX, it is recommended that you also enable the "DamageEvents" X option for enhanced performance. If you are using an OpenGL-based composite manager, you may also need the "DisableGLXRootClipping" option to obtain proper output. The Composite extension also causes problems with other driver components: o In X servers prior to X.Org 7.1, Xv cannot draw into pixmaps that have been redirected offscreen and will draw directly onto the screen instead. For some programs you can work around this issue by using an alternative video driver. For example, "mplayer -vo x11" will work correctly, as will "xine -V xshm". If you must use Xv with an older server, you can also disable the compositing manager and re-enable it when you are finished. On X.Org 7.1 and higher, the driver will properly redirect video into offscreen pixmaps. Note that the Xv adaptors will ignore the sync-to-vblank option when drawing into a redirected window. o Workstation overlays, stereo visuals, and the unified back buffer (UBB) are incompatible with Composite. These features will be automatically disabled when Composite is detected. o The Composite extension is currently incompatible with Xinerama, due to limitations in the X.Org X server. Composite will be automatically disabled when Xinerama is enabled. This NVIDIA Linux supports OpenGL rendering to 32-bit ARGB windows on X.Org 7.2 and higher or when the "AddARGBGLXVisuals" X config file option is enabled. 32-bit visuals are only available on screens with depths 24 or 30. If you are an application developer, you can use these new visuals in conjunction with a composite manager to create translucent OpenGL applications: int attrib[] = { GLX_RENDER_TYPE, GLX_RGBA_BIT, GLX_DRAWABLE_TYPE, GLX_WINDOW_BIT, GLX_RED_SIZE, 1, GLX_GREEN_SIZE, 1, GLX_BLUE_SIZE, 1, GLX_ALPHA_SIZE, 1, GLX_DOUBLEBUFFER, True, GLX_DEPTH_SIZE, 1, None }; GLXFBConfig *fbconfigs, fbconfig; int numfbconfigs, render_event_base, render_error_base; XVisualInfo *visinfo; XRenderPictFormat *pictFormat; /* Make sure we have the RENDER extension */ if(!XRenderQueryExtension(dpy, &render_event_base, &render_error_base)) { fprintf(stderr, "No RENDER extension found\n"); exit(EXIT_FAILURE); } /* Get the list of FBConfigs that match our criteria */ fbconfigs = glXChooseFBConfig(dpy, scrnum, attrib, &numfbconfigs); if (!fbconfigs) { /* None matched */ exit(EXIT_FAILURE); } /* Find an FBConfig with a visual that has a RENDER picture format that * has alpha */ for (i = 0; i < numfbconfigs; i++) { visinfo = glXGetVisualFromFBConfig(dpy, fbconfigs[i]); if (!visinfo) continue; pictFormat = XRenderFindVisualFormat(dpy, visinfo->visual); if (!pictFormat) continue; if(pictFormat->direct.alphaMask > 0) { fbconfig = fbconfigs[i]; break; } XFree(visinfo); } if (i == numfbconfigs) { /* None of the FBConfigs have alpha. Use a normal (opaque) * FBConfig instead */ fbconfig = fbconfigs[0]; visinfo = glXGetVisualFromFBConfig(dpy, fbconfig); pictFormat = XRenderFindVisualFormat(dpy, visinfo->visual); } XFree(fbconfigs); When rendering to a 32-bit window, keep in mind that the X RENDER extension, used by most composite managers, expects "premultiplied alpha" colors. This means that if your color has components (r,g,b) and alpha value a, then you must render (a*r, a*g, a*b, a) into the target window. More information about Composite can be found at http://freedesktop.org/Software/CompositeExt ______________________________________________________________________________ Chapter 24. Using the nvidia-settings Utility ______________________________________________________________________________ A graphical configuration utility, 'nvidia-settings', is included with the NVIDIA Linux graphics driver. After installing the driver and starting X, you can run this configuration utility by running: % nvidia-settings in a terminal window. Detailed information about the configuration options available are documented in the help window in the utility. For more information, see the nvidia-settings man page. The source code to nvidia-settings is released as GPL and is available here: ftp://download.nvidia.com/XFree86/nvidia-settings/ ______________________________________________________________________________ Chapter 25. Configuring SLI and Multi-GPU FrameRendering ______________________________________________________________________________ The NVIDIA Linux driver contains support for NVIDIA SLI FrameRendering and NVIDIA Multi-GPU FrameRendering. Both of these technologies allow an OpenGL application to take advantage of multiple GPUs to improve visual performance. The distinction between SLI and Multi-GPU is straightforward. SLI is used to leverage the processing power of GPUs across two or more graphics cards, while Multi-GPU is used to leverage the processing power of two GPUs colocated on the same graphics card. If you want to link together separate graphics cards, you should use the "SLI" X config option. Likewise, if you want to link together GPUs on the same graphics card, you should use the "MultiGPU" X config option. If you have two cards, each with two GPUs, and you wish to link them all together, you should use the "SLI" option. 25A. RENDERING MODES In Linux, with two GPUs SLI and Multi-GPU can both operate in one of three modes: Alternate Frame Rendering (AFR), Split Frame Rendering (SFR), and Antialiasing (AA). When AFR mode is active, one GPU draws the next frame while the other one works on the frame after that. In SFR mode, each frame is split horizontally into two pieces, with one GPU rendering each piece. The split line is adjusted to balance the load between the two GPUs. AA mode splits antialiasing work between the two GPUs. Both GPUs work on the same scene and the result is blended together to produce the final frame. This mode is useful for applications that spend most of their time processing with the CPU and cannot benefit from AFR. With four GPUs, the same options are applicable. AFR mode cycles through all four GPUs, each GPU rendering a frame in turn. SFR mode splits the frame horizontally into four pieces. AA mode splits the work between the four GPUs, allowing antialiasing up to 64x. With four GPUs SLI can also operate in an additional mode, Alternate Frame Rendering of Antialiasing. (AFR of AA). With AFR of AA, pairs of GPUs render alternate frames, each GPU in a pair doing half of the antialiasing work. Note that these scenarios apply whether you have four separate cards or you have two cards, each with two GPUs. With a Quadro Plex Visual Computing System (VCS), the same options as above are available, if your Quadro Plex VCS has two or four GPUs. In addition, there is a special SLI Mosaic Mode to extend a single X screen transparently across all of the available display outputs on the Quadro Plex VCS. 25B. ENABLING MULTI-GPU Multi-GPU is enabled by setting the "MultiGPU" option in the X configuration file; see Appendix B for details about the "MultiGPU" option. The nvidia-xconfig utility can be used to set the "MultiGPU" option, rather than modifying the X configuration file by hand. For example: % nvidia-xconfig --multigpu=on 25C. ENABLING SLI SLI is enabled by setting the "SLI" option in the X configuration file; see Appendix B for details about the SLI option. The nvidia-xconfig utility can be used to set the SLI option, rather than modifying the X configuration file by hand. For example: % nvidia-xconfig --sli=on 25D. ENABLING SLI MOSAIC MODE The simplest way to configure SLI Mosaic Mode using a grid of monitors is to use 'nvidia-settings' (see Chapter 24). The steps to perform this configuration are as follows: 1. Install your Quadro Plex VCS into the system, following the steps provided in the Quadro Plex Installation Guide. 2. Connect all of the monitors you would like to use to the Quadro Plex VCS. If you are going to use fewer monitors than there are connectors, connect one monitor to each GPU before adding a second monitor to any GPUs. 3. Install the NVIDIA display driver set. 4. Configure an X screen to use the "nvidia" driver on at least one of the GPUs in your Quadro Plex VCS (see Chapter 6 for more information). 5. Start X. 6. Run 'nvidia-settings'. You should see a tab in the left pane of nvidia-settings labeled "SLI Mosaic Mode Settings". Note that you may need to expand the entry for the X screen you configured earlier. 7. Check the "Use SLI Mosaic Mode" check box. 8. Select the monitor grid configuration you'd like to use from the "display configuration" dropdown. 9. Choose the resolution and refresh rate at which you would like to drive each individual monitor. 10. Set any overlap you would like between the displays. 11. Click the "Save to X Configuration File" button. NOTE: If you don't have permissions to write to your system's X configuration file, you will be prompted to choose a location to save the file. After doing so, you MUST copy the X configuration file into a location the X server will consider upon startup (usually '/etc/X11/xorg.conf' for X.Org servers or '/etc/X11/XF86Config' for XFree86 servers). 12. Exit nvidia-settings and restart your X server. Alternatively, nvidia-xconfig can be used to configure SLI Mosaic Mode via a command like 'nvidia-xconfig --sli=Mosaic --metamodes=METAMODES' where the METAMODES string specifies the desired grid configuration. For example: nvidia-xconfig --sli=Mosaic --metamodes="GPU-0.DFP-0: 1920x1024+0+0, GPU-0.DFP-1: 1920x1024+1920+0, GPU-1.DFP-0: 1920x1024+0+1024, GPU-1.DFP-1: 1920x1024+1920+1024" will configure four DFPs in a 2x2 configuration, each running at 1920x1024, with the two DFPs on GPU-0 driving the top two monitors of the 2x2 configuration, and the two DFPs on GPU-1 driving the bottom two monitors of the 2x2 configuration. See the MetaModes X configuration description in details in Chapter 13. See Appendix C for further details on GPU and Display Device Names. 25E. HARDWARE REQUIREMENTS SLI functionality requires: o Identical PCI-Express graphics cards o A supported motherboard o In most cases, a video bridge connecting the two graphics cards o A Quadro Plex VCS to use SLI Mosaic Mode For the latest in supported SLI and Multi-GPU configurations, including SLI- and Multi-GPU capable GPUs and SLI-capable motherboards, see http://www.slizone.com. 25F. OTHER NOTES AND REQUIREMENTS The following other requirements apply to SLI and Multi-GPU: o Mobile GPUs are NOT supported o SLI on Quadro-based graphics cards always requires a video bridge o TwinView is also not supported with SLI or Multi-GPU. Only one display can be used when SLI or Multi-GPU is enabled, with the exception of Mosaic. o If X is configured to use multiple screens and screen 0 has SLI or Multi-GPU enabled, the other screens configured to use the nvidia driver will be disabled. Note that if SLI or Multi-GPU is enabled, the GPUs used by that configuration will be unavailable for single GPU rendering. FREQUENTLY ASKED SLI AND MULTI-GPU QUESTIONS Q. Why is glxgears slower when SLI or Multi-GPU is enabled? A. When SLI or Multi-GPU is enabled, the NVIDIA driver must coordinate the operations of all GPUs when each new frame is swapped (made visible). For most applications, this GPU synchronization overhead is negligible. However, because glxgears renders so many frames per second, the GPU synchronization overhead consumes a significant portion of the total time, and the framerate is reduced. Q. Why is Doom 3 slower when SLI or Multi-GPU is enabled? A. The NVIDIA Accelerated Linux Graphics Driver does not automatically detect the optimal SLI or Multi-GPU settings for games such as Doom 3 and Quake 4. To work around this issue, the environment variable __GL_DOOM3 can be set to tell OpenGL that Doom 3's optimal settings should be used. In Bash, this can be done in the same command that launches Doom 3 so the environment variable does not remain set for other OpenGL applications started in the same session: % __GL_DOOM3=1 doom3 Doom 3's startup script can also be modified to set this environment variable: #!/bin/sh # Needed to make symlinks/shortcuts work. # the binaries must run with correct working directory cd "/usr/local/games/doom3/" export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:. export __GL_DOOM3=1 exec ./doom.x86 "$@" This environment variable is temporary and will be removed in the future. Q. Why does SLI or MultiGPU fail to initialize? A. There are several reasons why SLI or MultiGPU may fail to initialize. Most of these should be clear from the warning message in the X log file; e.g.: o "Unsupported bus type" o "The video link was not detected" o "GPUs do not match" o "Unsupported GPU video BIOS" o "Insufficient PCI-E link width" The warning message "'Unsupported PCI topology'" is likely due to problems with your Linux kernel. The NVIDIA driver must have access to the PCI Bridge (often called the Root Bridge) that each NVIDIA GPU is connected to in order to configure SLI or MultiGPU correctly. There are many kernels that do not properly recognize this bridge and, as a result, do not allow the NVIDIA driver to access this bridge. See the below "How can I determine if my kernel correctly detects my PCI Bridge?" FAQ for details. Below are some specific troubleshooting steps to help deal with SLI and MultiGPU initialization failures. o Make sure that ACPI is enabled in your kernel. NVIDIA's experience has been that ACPI is needed for the kernel to correctly recognize the Root Bridge. Note that in some cases, the kernel's version of ACPI may still have problems and require an update to a newer kernel. o Run 'lspci' to check that multiple NVIDIA GPUs can be identified by the operating system; e.g: % /sbin/lspci | grep -i nvidia If 'lspci' does not report all the GPUs that are in your system, then this is a problem with your Linux kernel, and it is recommended that you use a different kernel. Please note: the 'lspci' utility may be installed in a location other than '/sbin' on your system. If the above command fails with the error: "'/sbin/lspci: No such file or directory'", please try: % lspci | grep -i nvidia , instead. You may also need to install your distribution's "pciutils" package. o Make sure you have the most recent SBIOS available for your motherboard. o The PCI-Express slots on the motherboard must provide a minimum link width. Please make sure that the PCI Express slot(s) on your motherboard meet the following requirements and that you have connected the graphics board to the correct PCI Express slot(s): o A dual-GPU board needs a minimum of 8 lanes (i.e. x8 or x16) o A pair of single-GPU boards requires one of the following supported link width combinations: o x16 + x16 o x16 + x8 o x16 + x4 o x8 + x8 Q. How can I determine if my kernel correctly detects my PCI Bridge? A. As discussed above, the NVIDIA driver must have access to the PCI Bridge that each NVIDIA GPU is connected to in order to configure SLI or MultiGPU correctly. The following steps will identify whether the kernel correctly recognizes the PCI Bridge: o Identify both NVIDIA GPUs: % /sbin/lspci | grep -i vga 0a:00.0 VGA compatible controller: nVidia Corporation [...] 81:00.0 VGA compatible controller: nVidia Corporation [...] o Verify that each GPU is connected to a bus connected to the Root Bridge (note that the GPUs in the above example are on buses 0a and 81): % /sbin/lspci -t good: -+-[0000:80]-+-00.0 | +-01.0 | \-0e.0-[0000:81]----00.0 ... \-[0000:00]-+-00.0 +-01.0 +-01.1 +-0e.0-[0000:0a]----00.0 bad: -+-[0000:81]---00.0 ... \-[0000:00]-+-00.0 +-01.0 +-01.1 +-0e.0-[0000:0a]----00.0 Note that in the first example, bus 81 is connected to Root Bridge 80, but that in the second example there is no Root Bridge 80 and bus 81 is incorrectly connected at the base of the device tree. In the bad case, the only solution is to upgrade your kernel to one that properly detects your PCI bus layout. ______________________________________________________________________________ Chapter 26. Configuring Frame Lock and Genlock ______________________________________________________________________________ NOTE: Frame Lock and Genlock features are supported only on specific hardware, as noted below. Visual computing applications that involve multiple displays, or even multiple windows within a display, can require special signal processing and application controls in order to function properly. For example, in order to produce quality video recording of animated graphics, the graphics display must be synchronized with the video camera. As another example, applications presented on multiple displays must be synchronized in order to complete the illusion of a larger, virtual canvas. This synchronization is enabled through the frame lock and genlock capabilities of the NVIDIA driver. This section describes the setup and use of frame lock and genlock. 26A. DEFINITION OF TERMS GENLOCK: Genlock refers to the process of synchronizing the pixel scanning of one or more displays to an external synchronization source. NVIDIA Genlock requires the external signal to be either TTL or composite, such as used for NTSC, PAL, or HDTV. It should be noted that the NVIDIA Genlock implementation is guaranteed only to be frame-synchronized, and not necessarily pixel-synchronized. FRAME LOCK: Frame Lock involves the use of hardware to synchronize the frames on each display in a connected system. When graphics and video are displayed across multiple monitors, frame locked systems help maintain image continuity to create a virtual canvas. Frame lock is especially critical for stereo viewing, where the left and right fields must be in sync across all displays. In short, to enable genlock means to sync to an external signal. To enable frame lock means to sync 2 or more display devices to a signal generated internally by the hardware, and to use both means to sync 2 or more display devices to an external signal. SWAP SYNC: Swap sync refers to the synchronization of buffer swaps of multiple application windows. By means of swap sync, applications running on multiple systems can synchronize the application buffer swaps between all the systems. In order to work across multiple systems, swap sync requires that the systems are frame locked. G-SYNC DEVICE: A G-Sync Device refers to devices capable of Frame lock/Genlock. This can be a graphics card (Quadro FX 3000G) or a stand alone device (Quadro FX G-Sync). See "Supported Hardware" below. 26B. SUPPORTED HARDWARE Frame lock and genlock are supported for the following hardware: Card ---------------------------------------------------------------------- Quadro FX 3000G Quadro FX G-Sync, used in conjunction with a Quadro FX 4400, Quadro FX 4500, or Quadro FX 5500 Quadro FX G-Sync II, used in conjunction with a Quadro FX 4600, or Quadro FX 5600 26C. HARDWARE SETUP Before you begin, you should check that your hardware has been properly installed. If you are using the Quadro FX 3000G, the genlock/frame lock signal processing hardware is located on the dual-slot card itself, and after installing the card, no additional setup is necessary. If you are using the Quadro FX G-Sync card in conjunction with a graphics card, the following additional setup steps are required. These steps must be performed when the system is off. 1. On the Quadro FX G-Sync card, locate the fourteen-pin connector labeled "primary". If the associated ribbon cable is not already joined to this connector, do so now. If you plan to use frame lock or genlock in conjunction with SLI FrameRendering or Multi-GPU FrameRendering (see Chapter 25) or other multi-GPU configurations, you should connect the fourteen-pin connector labeled "secondary" to the second GPU. A section at the end of this appendix describes restrictions on such setups. 2. Install the Quadro FX G-Sync card in any available slot. Note that the slot itself is only used for support, so even a known "bad" slot is acceptable. The slot must be close enough to the graphics card that the ribbon cable can reach. 3. Connect the other end of the ribbon cable to the fourteen-pin connector on the graphics card. You may now boot the system and begin the software setup of genlock and/or frame lock. These instructions assume that you have already successfully installed the NVIDIA Accelerated Linux Driver Set. If you have not done so, see Chapter 4. 26D. CONFIGURATION WITH NVIDIA-SETTINGS GUI Frame lock and genlock are configured through the nvidia-settings utility. See the 'nvidia-settings(1)' man page, and the nvidia-settings online help (click the "Help" button in the lower right corner of the interface for per-page help information). From the nvidia-settings frame lock panel, you may control the addition of G-Sync (and display) devices to the frame lock/genlock group, monitor the status of that group, and enable/disable frame lock and genlock. After the system has booted and X Windows has been started, run nvidia-settings as % nvidia-settings You may wish to start this utility before continuing, as we refer to it frequently in the subsequent discussion. The setup of genlock and frame lock are described separately. We then describe the use of genlock and frame lock together. 26E. GENLOCK SETUP After the system has been booted, connect the external signal to the house sync connector (the BNC connector) on either the graphics card or the G-Sync card. There is a status LED next to the connector. A solid red LED indicates that the hardware cannot detect the timing signal. A green LED indicates that the hardware is detecting a timing signal. An occasional red flash is okay. The G-Sync device (graphics card or G-Sync card) will need to be configured correctly for the signal to be detected. In the frame lock panel of the nvidia-settings interface, add the X Server that contains the display and G-Sync devices that you would like to sync to this external source by clicking the "Add Devices..." button. An X Server is typically specified in the format "system:m", e.g.: mycomputer.domain.com:0 or localhost:0 After adding an X Server, rows will appear in the "G-Sync Devices" section on the frame lock panel that displays relevant status information about the G-Sync devices, GPUs attached to those G-Sync devices and the display devices driven by those GPUs. In particular, the G-Sync rows will display the server name and G-Sync device number along with "Receiving" LED, "Rate", "House" LED, "Port 0"/"Port 1" Images, and "Delay" information. The GPU rows will display the GPU product name information along with the GPU ID for the server. The Display Device rows will show the display device name and device type along with server/client check boxes, refresh rate, "Timing" LED and "Stereo" LED. Once the G-Sync and display devices have been added to the frame lock/genlock group, a Server display device will need to be selected. This is done by selecting the "Server" check box of the desired display device. If you are using a G-Sync card, you must also click the "Use House Sync if Present" check box. To enable synchronization of this G-Sync device to the external source, click the "Enable Frame Lock" button. The display device(s) may take a moment to stabilize. If it does not stabilize, you may have selected a synchronization signal that the system cannot support. You should disable synchronization by clicking the "Disable Frame Lock" button and check the external sync signal. Modifications to genlock settings (e.g., "Use House Sync if Present", "Add Devices...") must be done while synchronization is disabled. 26F. FRAME LOCK SETUP Frame Lock is supported across an arbitrary number of Quadro FX 3000 or Quadro FX G-Sync systems, although mixing the two in the same frame lock group is not supported. Additionally, each system to be included in the frame lock group must be configured with identical mode timings. See Chapter 19 for information on mode timings. Connect the systems through their RJ45 ports using standard CAT5 patch cables. These ports are located on the frame lock card itself (either the Quadro FX 3000 or the Quadro FX G-Sync card). DO NOT CONNECT A FRAME LOCK PORT TO AN ETHERNET CARD OR HUB. DOING SO MAY PERMANENTLY DAMAGE THE HARDWARE. The connections should be made in a daisy-chain fashion: each card has two RJ45 ports, call them 1 and 2. Connect port 1 of system A to port 2 of system B, connect port 1 of system B to port 2 of system C, etc. Note that you will always have two empty ports in your frame lock group. The ports self-configure as inputs or outputs once frame lock is enabled. Each port has a yellow and a green LED that reflect this state. A flashing yellow LED indicates an output and a flashing green LED indicates an input. A solid green LED indicates that the port has not yet configured. In the frame lock panel of the nvidia-settings interface, add the X server that contains the display devices that you would like to include in the frame lock group by clicking the "Add Devices..." button (see the description for adding display devices in the previous section on GENLOCK SETUP. Like the genlock status indicators, the "Port 0" and "Port 1" columns in the table on the frame lock panel contain indicators whose states mirror the states of the physical LEDs on the RJ45 ports. Thus, you may monitor the status of these ports from the software interface. Any X Server can be added to the frame lock group, provided that 1. The system supporting the X Server is configured to support frame lock and is connected via RJ45 cable to the other systems in the frame lock group. 2. The system driving nvidia-settings can locate and has display privileges on the X server that is to be included for frame lock. A system can gain display privileges on a remote system by executing % xhost + on the remote system. See the xhost(1) man page for details. Typically, frame lock is controlled through one of the systems that will be included in the frame lock group. While this is not a requirement, note that nvidia-settings will only display the frame lock panel when running on an X server that supports frame lock. To enable synchronization on these display devices, click the "Enable Frame Lock" button. The screens may take a moment to stabilize. If they do not stabilize, you may have selected mode timings that one or more of the systems cannot support. In this case you should disable synchronization by clicking the "Disable Frame Lock" button and refer to Chapter 19 for information on mode timings. Modifications to frame lock settings (e.g. "Add/Remove Devices...") must be done while synchronization is disabled. nvidia-settings will not automatically enable Frame Lock via the nvidia-settings.rc file. To enable Frame Lock when starting the X server, a line such as the following can be added to the '~/.xinitrc' file: # nvidia-settings -a [gpu:0]/FrameLockEnable=1 26G. FRAME LOCK + GENLOCK The use of frame lock and genlock together is a simple extension of the above instructions for using them separately. You should first follow the instructions for Frame Lock Setup, and then to one of the systems that will be included in the frame lock group, attach an external sync source. In order to sync the frame lock group to this single external source, you must select a display device driven by the GPU connected to the G-Sync card (through the primary connector) that is connected to the external source to be the signal server for the group. This is done by selecting the check box labeled "Server" of the tree on the frame lock panel in nvidia-settings. If you are using a G-Sync based frame lock group, you must also select the "Use House Sync if Present" check box. Enable synchronization by clicking the "Enable Frame Lock" button. As with other frame lock/genlock controls, you must select the signal server while synchronization is disabled. 26H. CONFIGURATION WITH NVIDIA-SETTINGS COMMAND LINE Frame Lock may also be configured through the nvidia-settings command line. This method of configuring Frame Lock may be useful in a scripted environment to automate the setup process. (Note that the examples listed below depend on the actual hardware configuration and as such may not work as-is.) To properly configure Frame Lock, the following steps should be completed: 1. Make sure Frame Lock Sync is disabled on all GPUs. 2. Make sure all display devices that are to be frame locked have the same refresh rate. 3. Configure which (display/GPU) device should be the master. 4. Configure house sync (if applicable). 5. Configure the slave display devices. 6. Enable frame lock sync on the master GPU. 7. Enable frame lock sync on the slave GPUs. 8. Toggle the test signal on the master GPU (for testing the hardware connectivity.) For a full list of the nvidia-settings Frame Lock attributes, please see the 'nvidia-settings(1)' man page. Examples: 1. 1 System, 1 Frame Lock board, 1 GPU, and 1 display device syncing to the house signal: # - Make sure frame lock sync is disabled nvidia-settings -a [gpu:0]/FrameLockEnable=0 nvidia-settings -q [gpu:0]/FrameLockEnable # - Query the enabled displays on the gpu nvidia-settings -q [gpu:0]/EnabledDisplays # - Check that the refresh rate is the one we want nvidia-settings -q [gpu:0]/RefreshRate # - Set the master display device to CRT-0. The desired display # device(s) to be set are passed in as a hexadecimal number # in which specific bits denote which display devices to set. # examples: # # 0x00000001 - CRT-0 # 0x00000002 - CRT-1 # 0x00000003 - CRT-0 and CRT-1 # # 0x00000100 - TV-0 # 0x00000200 - TV-1 # # 0x00020000 - DFP-1 # # 0x00010101 - CRT-0, TV-0 and DFP-0 # # 0x000000FF - All CRTs # 0x0000FF00 - All TVs # 0x00FF0000 - All DFPs # # Note that the following command: # # nvidia-settings -q [gpu:0]/EnabledDisplays # # will list the available displays on the given GPU. nvidia-settings -a [gpu:0]/FrameLockMaster=0x00000001 nvidia-settings -q [gpu:0]/FrameLockMaster # - Enable use of house sync signal nvidia-settings -a [framelock:0]/FrameLockUseHouseSync=1 # - Configure the house sync signal video mode nvidia-settings -a [framelock:0]/FrameLockVideoMode=0 # - Set the slave display device to none (to avoid # having unwanted display devices locked to the # sync signal.) nvidia-settings -a [gpu:0]/FrameLockSlaves=0x00000000 nvidia-settings -q [gpu:0]/FrameLockSlaves # - Enable frame lock nvidia-settings -a [gpu:0]/FrameLockEnable=1 # - Toggle the test signal nvidia-settings -a [gpu:0]/FrameLockTestSignal=1 nvidia-settings -a [gpu:0]/FrameLockTestSignal=0 2. 2 Systems, each with 2 GPUs, 1 Frame Lock board and 1 display device per GPU syncing from the first system's first display device: # - Make sure frame lock sync is disabled nvidia-settings -a myserver:0[gpu:0]/FrameLockEnable=0 nvidia-settings -a myserver:0[gpu:1]/FrameLockEnable=0 nvidia-settings -a myslave1:0[gpu:0]/FrameLockEnable=0 nvidia-settings -a myslave1:0[gpu:1]/FrameLockEnable=0 # - Query the enabled displays on the GPUs nvidia-settings -q myserver:0[gpu:0]/EnabledDisplays nvidia-settings -q myserver:0[gpu:1]/EnabledDisplays nvidia-settings -q myslave1:0[gpu:0]/EnabledDisplays nvidia-settings -q myslave1:0[gpu:1]/EnabledDisplays # - Check the refresh rate is the same for all displays nvidia-settings -q myserver:0[gpu:0]/RefreshRate nvidia-settings -q myserver:0[gpu:1]/RefreshRate nvidia-settings -q myslave1:0[gpu:0]/RefreshRate nvidia-settings -q myslave1:0[gpu:1]/RefreshRate # - Make sure the display device we want as master is masterable nvidia-settings -q myserver:0[gpu:0]/FrameLockMasterable # - Set the master display device (CRT-0) nvidia-settings -a myserver:0[gpu:0]/FrameLockMaster=0x00000001 # - Disable the house sync signal on the master device nvidia-settings -a myserver:0[framelock:0]/FrameLockUseHouseSync=0 # - Set the slave display devices nvidia-settings -a myserver:0[gpu:1]/FrameLockSlaves=0x00000001 nvidia-settings -a myslave1:0[gpu:0]/FrameLockSlaves=0x00000001 nvidia-settings -a myslave1:0[gpu:1]/FrameLockSlaves=0x00000001 # - Enable frame lock on server nvidia-settings -a myserver:0[gpu:0]/FrameLockEnable=1 # - Enable frame lock on slave devices nvidia-settings -a myserver:0[gpu:1]/FrameLockEnable=1 nvidia-settings -a myslave1:0[gpu:0]/FrameLockEnable=1 nvidia-settings -a myslave1:0[gpu:1]/FrameLockEnable=1 # - Toggle the test signal nvidia-settings -a myserver:0[gpu:0]/FrameLockTestSignal=1 nvidia-settings -a myserver:0[gpu:0]/FrameLockTestSignal=0 3. 1 System, 4 GPUs, 2 Frame Lock boards and 2 display devices per GPU syncing from the first GPU's display device: # - Make sure frame lock sync is disabled nvidia-settings -a [gpu:0]/FrameLockEnable=0 nvidia-settings -a [gpu:1]/FrameLockEnable=0 nvidia-settings -a [gpu:2]/FrameLockEnable=0 nvidia-settings -a [gpu:3]/FrameLockEnable=0 # - Query the enabled displays on the GPUs nvidia-settings -q [gpu:0]/EnabledDisplays nvidia-settings -q [gpu:1]/EnabledDisplays nvidia-settings -q [gpu:2]/EnabledDisplays nvidia-settings -q [gpu:3]/EnabledDisplays # - Check the refresh rate is the same for all displays nvidia-settings -q [gpu:0]/RefreshRate nvidia-settings -q [gpu:1]/RefreshRate nvidia-settings -q [gpu:2]/RefreshRate nvidia-settings -q [gpu:3]/RefreshRate # - Make sure the display device we want as master is masterable nvidia-settings -q myserver:0[gpu:0]/FrameLockMasterable # - Set the master display device (CRT-0) nvidia-settings -a [gpu:0]/FrameLockMaster=0x00000001 # - Disable the house sync signal on the master device nvidia-settings -a [framelock:0]/FrameLockUseHouseSync=0 # - Set the slave display devices nvidia-settings -a [gpu:0]/FrameLockSlaves=0x00000002 # CRT-1 nvidia-settings -a [gpu:1]/FrameLockSlaves=0x00000003 # CRT-0 and CRT-1 nvidia-settings -a [gpu:2]/FrameLockSlaves=0x00000003 # CRT-0 and CRT-1 nvidia-settings -a [gpu:3]/FrameLockSlaves=0x00000003 # CRT-0 and CRT-1 # - Enable frame lock on master GPU nvidia-settings -a [gpu:0]/FrameLockEnable=1 # - Enable frame lock on slave devices nvidia-settings -a [gpu:1]/FrameLockEnable=1 nvidia-settings -a [gpu:2]/FrameLockEnable=1 nvidia-settings -a [gpu:3]/FrameLockEnable=1 # - Toggle the test signal nvidia-settings -a [gpu:0]/FrameLockTestSignal=1 nvidia-settings -a [gpu:0]/FrameLockTestSignal=0 26I. LEVERAGING FRAME LOCK/GENLOCK IN OPENGL With the GLX_NV_swap_group extension, OpenGL applications can be implemented to join a group of applications within a system for local swap sync, and bind the group to a barrier for swap sync across a frame lock group. A universal frame counter is also provided to promote synchronization across applications. 26J. FRAME LOCK RESTRICTIONS: The following restrictions must be met for enabling frame lock: 1. All display devices set as client in a frame lock group must have the same mode timings as the server (master) display device. If a House Sync signal is used (instead of internal timings), all client display devices must be set to have the same refresh rate as the incoming house sync signal. 2. All X Screens (driving the selected client/server display devices) must have the same stereo setting. See Appendix B for instructions on how to set the stereo X option. 3. The frame lock server (master) display device must be on a GPU on the primary connector to a G-Sync device. 4. If connecting a single GPU to a G-Sync device, the primary connector must be used. 5. In configurations with more than one display device per GPU, we recommend enabling frame lock on all display devices on those GPUs. 6. Virtual terminal switching or mode switching will disable frame lock on the display device. Note that the glXQueryFrameCountNV entry point (provided by the GLX_NV_swap_group extension) will only provide incrementing numbers while frame lock is enabled. Therefore, applications that use glXQueryFrameCountNV to control animation will appear to stop animating while frame lock is disabled. 26K. SUPPORTED FRAME LOCK CONFIGURATIONS: The following configurations are currently supported: 1. Basic Frame Lock: Single GPU, Single X Screen, Single Display Device with or without OpenGL applications that make use of Quad-Buffered Stereo and/or the GLX_NV_swap_group extension. 2. Frame Lock + TwinView: Single GPU, Single X Screen, Multiple Display Devices with or without OpenGL applications that make use of Quad-Buffered Stereo and/or the GLX_NV_swap_group extension. 3. Frame Lock + Xinerama: 1 or more GPU(s), Multiple X Screens, Multiple Display Devices with or without OpenGL applications that make use of Quad-Buffered Stereo and/or the GLX_NV_swap_group extension. 4. Frame Lock + TwinView + Xinerama: 1 or more GPU(s), Multiple X Screens, Multiple Display Devices with or without OpenGL applications that make use of Quad-Buffered Stereo and/or the GLX_NV_swap_group extension. 5. Frame Lock + SLI SFR, AFR, or AA: 2 GPUs, Single X Screen, Single Display Device with either OpenGL applications that make use of Quad-Buffered Stereo or the GLX_NV_swap_group extension. Note that for Frame Lock + SLI Frame Rendering applications that make use of both Quad-Buffered Stereo and the GLX_NV_swap_group extension are not supported. Note that only 2-GPU SLI configurations are currently supported. 6. Frame Lock + Multi-GPU SFR, AFR, or AA: 2 GPUs, Single X Screen, Single Display Device with either OpenGL applications that make use of Quad-Buffered Stereo or the GLX_NV_swap_group extension. Note that for Frame Lock + Multi-GPU Frame Rendering applications that make use of both Quad-Buffered Stereo and the GLX_NV_swap_group extension are not supported. ______________________________________________________________________________ Chapter 27. Configuring SDI Video Output ______________________________________________________________________________ Broadcast, film, and video post production and digital cinema applications can require Serial Digital (SDI) or High Definition Serial Digital (HD-SDI) video output. SDI/HD-SDI is a digital video interface used for the transmission of uncompressed video signals as well as packetized data. SDI is standardized in ITU-R BT.656 and SMPTE 259M while HD-SDI is standardized in SMPTE 292M. SMPTE 372M extends HD-SDI to define a dual-link configuration that uses a pair of SMPTE 292M links to provide a 2.970 Gbit/second interface. SMPTE 424M extends the interface further to define a single 2.97 Gbit/second serial data link. SDI and HD-SDI video output is provided through the use of the NVIDIA driver along with an NVIDIA SDI output daughter board. In addition to single- and dual-link SDI/HD-SDI digital video output, frame lock and genlock synchronization are provided in order to synchronize the outgoing video with an external source signal (see Chapter 26 for details on these technologies). This section describes the setup and use of the SDI video output. 27A. HARDWARE SETUP Before you begin, you should check that your hardware has been properly installed. If you are using the Quadro FX 4000 SDI, the SDI/HD-SDI hardware is located on the dual-slot card itself, and after installing the card, no additional setup is necessary. If you are using the Quadro FX 4500/5500 SDI or Quadro FX 4600/5600 SDI II, the following additional setup steps are required in order to connect the SDI daughter card to the graphics card. These steps must be performed when the system is off. 1. Insert the NVIDIA SDI Output card into any available expansion slot within six inches of the NVIDIA Quadro graphics card. Secure the card's bracket using the method provided by the chassis manufacturer (usually a thumb screw or an integrated latch). 2. Connect one end of the 14-pin ribbon cable to the G-Sync connector on the NVIDIA Quadro graphics card, and the other end to the NVIDIA SDI output card. 3. On Quadro FX 4500/5500 SDI, connect the SMA-to-BNC cables by screwing the male SMA connectors onto the female SMA connectors on the NVIDIA SDI output card. On Quadro FX 4600/5600 SDI II, this step is not necessary: the SDI II has BNC connectors rather than SMA connectors. 4. Connect the DVI-loopback connector by connecting one end of the DVI cable to the DVI connector on the NVIDIA SDI output card and the other end to the "north" DVI connector on the NVIDIA Quadro graphics card. The "north" DVI connector on the NVIDIA Quadro graphics card is the DVI connector that is the farthest from the graphics card PCI-E connection to the motherboard. The SDI output card will NOT function properly if this cable is connected to the "south" DVI connector. Once the above installation is complete, you may boot the system and configure the SDI video output using nvidia-settings. These instructions assume that you have already successfully installed the NVIDIA Linux Accelerated Graphics Driver. If you have not done so, see Chapter 4 for details. 27B. CLONE MODE CONFIGURATION WITH 'nvidia-settings' SDI video output is configured through the nvidia-settings utility. See the 'nvidia-settings(1)' man page, and the nvidia-settings online help (click the "Help" button in the lower right corner of the interface for per-page help information). After the system has booted and X Windows has been started, run nvidia-settings as % nvidia-settings When the NVIDIA X Server Settings page appears, follow the steps below to configure the SDI video output. 1. Click on the "Graphics to Video Out" tree item on the side menu. This will open the "Graphics to Video Out" page. 2. Go to the "Synchronization Options" subpage and choose a synchronization method. From the "Sync Options" drop down click the list arrow to the right and then click the method that you want to use to synchronize the SDI output. Sync Method Description ------------- -------------------------------------------------- Free Running The SDI output will be synchronized with the timing chosen from the SDI signal format list. Genlock SDI output will be synchronized with the external sync signal. Frame Lock The SDI output will be synchronized with the timing chosen from the SDI signal format list. In this case, the list of available timings is limited to those timings that can be synchronized with the detected external sync signal. Note that on Quadro FX 4600/5600 SDI II, you must first choose the correct Sync Format before an incoming sync signal will be detected. 3. From the top Graphics to Video Out page, choose the output video format that will control the video resolution, field rate, and SMPTE signaling standard for the outgoing video stream. From the "Clone Mode" drop down box, click the "Video Format" arrow and then click the signal format that you would like to use. Note that only those resolutions that are smaller or equal to the desktop resolution will be available. Also, this list is pruned according to the sync option selected. If genlock synchronization is chosen, the output video format is automatically set to match the incoming video sync format and this drop down list will be grayed out preventing you from choosing another format. If frame lock synchronization has been selected, then only those modes that are compatible with the detected sync signal will be available. 4. Choose the output data format from the "Output Data Format" drop down list. 5. Click the "Enable SDI Output" button to enable video output using the settings above. The status of the SDI output can be verified by examining the LED indicators in the "Graphics to SDI property" page banner. 6. To subsequently stop SDI output, simply click on the button that now says "Disable SDI Output". 7. In order to change any of the SDI output parameters such as the Output Video Format, Output Data Format as well as the Synchronization Delay, it is necessary to first disable the SDI output. 27C. CONFIGURATION FOR TWINVIEW OR AS A SEPARATE X SCREEN SDI video output can be configured through the nvidia-settings X Server Display Configuration page, for use in TwinView or as a separate X screen. The SDI video output can be configured as if it were a digital flat panel, choosing the resolution, refresh rate, and position within the desktop. Similarly, the SDI video output can be configured for use in TwinView or as a separate X screen through the X configuration file. The supported SDI video output modes can be requested by name anywhere a mode name can be used in the X configuration file (either in the "Modes" line, or in the "MetaModes" option). E.g., Option "MetaModes" "CRT-0:nvidia-auto-select, DFP-1:1280x720_60.00_smpte296" The mode names are reported in the nvidia-settings Display Configuration page when in advanced mode. As well, the initial output data format, sync mode and sync source can be set via the Appendix B, Appendix B, and Appendix B. See Appendix B for instructions on how to set these X options. Note that SDI "Clone Mode" as configured through the Graphics to Video Out page in nvidia-settings is mutually exclusive with using the SDI video output in TwinView or as a separate X screen. ______________________________________________________________________________ Chapter 28. Configuring Depth 30 Displays ______________________________________________________________________________ This driver release supports X screens with screen depths of 30 bits per pixel (10 bits per color component) on NVIDIA Quadro GPUs based on G80 and higher chip architectures. This provides about 1 billion possible colors, allowing for higher color precision and smoother gradients. When displaying a depth 30 image, the color data may be dithered to lower bit depths, depending on the capabilities of the display device and how it is connected to the GPU. Some devices connected via analog VGA or DisplayPort can display the full 10 bit range of colors. Devices connected via DVI or HDMI, as well as laptop internal panels connected via LVDS, will be dithered to 8 or 6 bits per pixel. To work reliably, depth 30 requires X.Org 7.3 or higher and pixman 0.11.6 or higher. In addition to the above software requirements, many X applications and toolkits do not understand depth 30 visuals as of this writing. Some programs may work correctly, some may work but display incorrect colors, and some may simply fail to run. In particular, many OpenGL applications request 8 bits of alpha when searching for FBConfigs. Since depth 30 visuals have only 2 bits of alpha, no suitable FBConfigs will be found and such applications will fail to start. ______________________________________________________________________________ Chapter 29. NVIDIA Contact Info and Additional Resources ______________________________________________________________________________ There is an NVIDIA Linux Driver web forum. You can access it by going to http://www.nvnews.net and following the "Forum" and "Linux Discussion Area" links. This is the preferable tool for seeking help; users can post questions, answer other users' questions, and search the archives of previous postings. If all else fails, you can contact NVIDIA for support at: linux-bugs@nvidia.com. But please, only send email to this address after you have explored the Chapter 7 and Chapter 8 chapters of this document, and asked for help on the nvnews.net web forum. When emailing linux-bugs@nvidia.com, please include the 'nvidia-bug-report.log.gz' file generated by the 'nvidia-bug-report.sh' script (which is installed as part of driver installation). Additional Resources Linux OpenGL ABI http://www.opengl.org/registry/ABI/ The XFree86 Project http://www.xfree86.org/ XFree86 Video Timings HOWTO http://www.tldp.org/HOWTO/XFree86-Video-Timings-HOWTO/index.html The X.Org Foundation http://www.x.org/ OpenGL http://www.opengl.org/ ______________________________________________________________________________ Chapter 30. Acknowledgements ______________________________________________________________________________ loki_update 'nvidia-installer' was inspired by the 'loki_update' tool: http://icculus.org/loki_setup// snarf The FTP and HTTP support in 'nvidia-installer' is based upon 'snarf 7.0': http://www.xach.com/snarf/ makeself The self-extracting archive (also known as the '.run' file) is generated using 'makeself.sh': http://www.megastep.org/makeself/ LLVM Portions of the NVIDIA OpenCL implementation contain components licensed from third parties under the following terms: Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal with the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: o Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers. o Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution. o Neither the names of the LLVM Team, University of Illinois at Urbana-Champaign, nor the names of its contributors may be used to endorse or promote products derived from this Software without specific prior written permission. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE CONTRIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS WITH THE SOFTWARE. PNG Library The NVIDIA X driver splash screen is decoded using 'libpng': http://libpng.org/pub/png/libpng.html X.Org int10 Emulator This NVIDIA Linux driver contains code from the int10 module of the X.Org project. NetBSD Compiler Intrinsics The NetBSD implementations of the following compiler intrinsics are used for better portability: __udivdi3, __umoddi3, __divdi3, __moddi3, __ucmpdi2, __cmpdi2, __fixunssfdi, __fixunsdfdi, __ashldi3 and __lshrdi3. These carry the following copyright notice: Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved. This software was developed by the Computer Systems Engineering group at Lawrence Berkeley Laboratory under DARPA contract BG 91-66 and contributed to Berkeley. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the University of California, Berkeley and its contributors. 4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ______________________________________________________________________________ Appendix A. Supported NVIDIA GPU Products ______________________________________________________________________________ For the most complete and accurate listing of supported GPUs, please see the Supported Products List, available from the NVIDIA Linux x86 Graphics Driver download page. Please go to http://www.nvidia.com/object/unix.html, follow the Archive link under the Linux x86 heading, follow the link for the 256.29 driver, and then go to the Supported Products List. For an explanation of the VDPAU features column, please refer to the section called "VdpDecoder" of Appendix H. A1. NVIDIA GEFORCE GPUS NVIDIA GPU product Device PCI ID VDPAU features ---------------------------------- --------------- --------------- GeForce 6800 Ultra 0x0040 - GeForce 6800 0x0041 - GeForce 6800 LE 0x0042 - GeForce 6800 XE 0x0043 - GeForce 6800 XT 0x0044 - GeForce 6800 GT 0x0045 - GeForce 6800 GT 0x0046 - GeForce 6800 GS 0x0047 - GeForce 6800 XT 0x0048 - GeForce 7800 GTX 0x0090 - GeForce 7800 GTX 0x0091 - GeForce 7800 GT 0x0092 - GeForce 7800 GS 0x0093 - GeForce 7800 SLI 0x0095 - GeForce Go 7800 0x0098 - GeForce Go 7800 GTX 0x0099 - GeForce 6800 GS 0x00C0 - GeForce 6800 0x00C1 - GeForce 6800 LE 0x00C2 - GeForce 6800 XT 0x00C3 - GeForce Go 6800 0x00C8 - GeForce Go 6800 Ultra 0x00C9 - GeForce 6600 GT 0x00F1 - GeForce 6600 0x00F2 - GeForce 6200 0x00F3 - GeForce 6600 LE 0x00F4 - GeForce 7800 GS 0x00F5 - GeForce 6800 GS 0x00F6 - GeForce 6800 Ultra 0x00F9 - GeForce 6600 GT 0x0140 - GeForce 6600 0x0141 - GeForce 6600 LE 0x0142 - GeForce 6600 VE 0x0143 - GeForce Go 6600 0x0144 - GeForce 6610 XL 0x0145 - GeForce Go 6600 TE/6200 TE 0x0146 - GeForce 6700 XL 0x0147 - GeForce Go 6600 0x0148 - GeForce Go 6600 GT 0x0149 - GeForce 6200 0x014F - GeForce 6500 0x0160 - GeForce 6200 TurboCache(TM) 0x0161 - GeForce 6200SE TurboCache(TM) 0x0162 - GeForce 6200 LE 0x0163 - GeForce Go 6200 0x0164 - GeForce Go 6400 0x0166 - GeForce Go 6200 0x0167 - GeForce Go 6400 0x0168 - GeForce 6250 0x0169 - GeForce 7100 GS 0x016A - GeForce 8800 GTX 0x0191 - GeForce 8800 GTS 0x0193 - GeForce 8800 Ultra 0x0194 - Tesla C870 0x0197 - GeForce 7350 LE 0x01D0 - GeForce 7300 LE 0x01D1 - GeForce 7550 LE 0x01D2 - GeForce 7300 SE/7200 GS 0x01D3 - GeForce Go 7200 0x01D6 - GeForce Go 7300 0x01D7 - GeForce Go 7400 0x01D8 - GeForce 7500 LE 0x01DD - GeForce 7300 GS 0x01DF - GeForce 6200 0x0221 - GeForce 6200 A-LE 0x0222 - GeForce 6150 0x0240 - GeForce 6150 LE 0x0241 - GeForce 6100 0x0242 - GeForce Go 6150 0x0244 - GeForce Go 6100 0x0247 - GeForce 7900 GTX 0x0290 - GeForce 7900 GT/GTO 0x0291 - GeForce 7900 GS 0x0292 - GeForce 7950 GX2 0x0293 - GeForce 7950 GX2 0x0294 - GeForce 7950 GT 0x0295 - GeForce Go 7950 GTX 0x0297 - GeForce Go 7900 GS 0x0298 - GeForce 7600 GT 0x02E0 - GeForce 7600 GS 0x02E1 - GeForce 7300 GT 0x02E2 - GeForce 7900 GS 0x02E3 - GeForce 7950 GT 0x02E4 - GeForce 7650 GS 0x038B - GeForce 7650 GS 0x0390 - GeForce 7600 GT 0x0391 - GeForce 7600 GS 0x0392 - GeForce 7300 GT 0x0393 - GeForce 7600 LE 0x0394 - GeForce 7300 GT 0x0395 - GeForce Go 7700 0x0397 - GeForce Go 7600 0x0398 - GeForce Go 7600 GT 0x0399 - GeForce 6150SE nForce 430 0x03D0 - GeForce 6100 nForce 405 0x03D1 - GeForce 6100 nForce 400 0x03D2 - GeForce 6100 nForce 420 0x03D5 - GeForce 7025 / nForce 630a 0x03D6 - GeForce 8600 GTS 0x0400 A GeForce 8600 GT 0x0401 A GeForce 8600 GT 0x0402 A GeForce 8600 GS 0x0403 A GeForce 8400 GS 0x0404 A GeForce 9500M GS 0x0405 A GeForce 8300 GS 0x0406 - GeForce 8600M GT 0x0407 A GeForce 9650M GS 0x0408 A GeForce 8700M GT 0x0409 A GeForce GT 330 0x0410 A GeForce 8400 SE 0x0420 - GeForce 8500 GT 0x0421 A GeForce 8400 GS 0x0422 A GeForce 8300 GS 0x0423 - GeForce 8400 GS 0x0424 A GeForce 8600M GS 0x0425 A GeForce 8400M GT 0x0426 A GeForce 8400M GS 0x0427 A GeForce 8400M G 0x0428 A GeForce 9400 GT 0x042C A GeForce 9300M G 0x042E A GeForce 7150M / nForce 630M 0x0531 - GeForce 7000M / nForce 610M 0x0533 - GeForce 7050 PV / nForce 630a 0x053A - GeForce 7050 PV / nForce 630a 0x053B - GeForce 7025 / nForce 630a 0x053E - GeForce GTX 295 0x05E0 A GeForce GTX 280 0x05E1 A GeForce GTX 260 0x05E2 A GeForce GTX 285 0x05E3 A GeForce GTX 275 0x05E6 A Tesla C1060 0x05E7 A GeForce GTX 260 0x05EA A GeForce GTX 295 0x05EB A GeForce 8800 GTS 512 0x0600 A GeForce 9800 GT 0x0601 A GeForce 8800 GT 0x0602 A GeForce GT 230 0x0603 A GeForce 9800 GX2 0x0604 A GeForce 9800 GT 0x0605 A GeForce 8800 GS 0x0606 A GeForce GTS 240 0x0607 A GeForce 9800M GTX 0x0608 A GeForce 8800M GTS 0x0609 A GeForce GTX 280M 0x060A A GeForce 9800M GT 0x060B A GeForce 8800M GTX 0x060C A GeForce 8800 GS 0x060D A GeForce GTX 285M 0x060F A GeForce 9600 GSO 0x0610 A GeForce 8800 GT 0x0611 A GeForce 9800 GTX/9800 GTX+ 0x0612 A GeForce 9800 GTX+ 0x0613 A GeForce 9800 GT 0x0614 A GeForce GTS 250 0x0615 A GeForce 9800M GTX 0x0617 A GeForce GTX 260M 0x0618 A GeForce 9600 GT 0x0622 A GeForce 9600 GS 0x0623 A GeForce 9600 GSO 512 0x0625 A GeForce GT 130 0x0626 A GeForce GT 140 0x0627 A GeForce 9800M GTS 0x0628 A GeForce 9700M GTS 0x062A A GeForce 9800M GS 0x062B A GeForce 9800M GTS 0x062C A GeForce 9600 GT 0x062D A GeForce 9600 GT 0x062E A GeForce GTS 160M 0x0631 A GeForce GTS 150M 0x0632 A GeForce 9600 GSO 0x0635 A GeForce 9600 GT 0x0637 A GeForce 9500 GT 0x0640 A GeForce 9400 GT 0x0641 A GeForce 9500 GT 0x0643 A GeForce 9500 GS 0x0644 A GeForce 9500 GS 0x0645 A GeForce GT 120 0x0646 A GeForce 9600M GT 0x0647 A GeForce 9600M GS 0x0648 A GeForce 9600M GT 0x0649 A GeForce 9700M GT 0x064A A GeForce 9500M G 0x064B A GeForce 9650M GT 0x064C A GeForce G 110M 0x0651 A GeForce GT 130M 0x0652 A GeForce GT 120M 0x0653 A GeForce GT 220M 0x0654 A GeForce 9650 S 0x0656 A GeForce 9400 GT 0x065B A GeForce GTX 480 0x06C0 C GeForce GTX 470 0x06CD C Tesla C2050 0x06D1 C Tesla M2050 0x06DE C GeForce 9300 GE 0x06E0 B 1 GeForce 9300 GS 0x06E1 B 1 GeForce 8400 0x06E2 B 1 GeForce 8400 SE 0x06E3 - GeForce 8400 GS 0x06E4 A 1 GeForce 9300M GS 0x06E5 B 1 GeForce G100 0x06E6 B 1 GeForce 9300 SE 0x06E7 - GeForce 9200M GS 0x06E8 B 1 GeForce 9300M GS 0x06E9 B 1 GeForce G 105M 0x06EC B 1 GeForce G 103M 0x06EF B 1 GeForce G105M 0x06F1 B 1 GeForce 7150 / nForce 630i 0x07E0 - GeForce 7100 / nForce 630i 0x07E1 - GeForce 7050 / nForce 630i 0x07E2 - GeForce 7050 / nForce 610i 0x07E3 - GeForce 7050 / nForce 620i 0x07E5 - GeForce 9100M G 0x0844 B 1 GeForce 8200M G 0x0845 B 1 GeForce 9200 0x0846 B 1 GeForce 9100 0x0847 B 1 GeForce 8300 0x0848 B 1 GeForce 8200 0x0849 B 1 nForce 730a 0x084A B 1 GeForce 9200 0x084B B 1 nForce 980a/780a SLI 0x084C B 1 nForce 750a SLI 0x084D B 1 GeForce 8100 / nForce 720a 0x084F - GeForce 9400 0x0860 B 1 GeForce 9400 0x0861 B 1 GeForce 9400M G 0x0862 B 1 GeForce 9400M 0x0863 B 1 GeForce 9300 0x0864 B 1 ION 0x0865 B 1 GeForce 9400M G 0x0866 B 1 GeForce 9400 0x0867 B 1 nForce 760i SLI 0x0868 B 1 GeForce 9400 0x086A B 1 GeForce 9300 / nForce 730i 0x086C B 1 GeForce 9200 0x086D B 1 GeForce 9100M G 0x086E B 1 GeForce 8200M G 0x086F B 1 GeForce 9400M 0x0870 B 1 GeForce 9200 0x0871 B 1 GeForce G102M 0x0872 B 1 GeForce G102M 0x0873 B 1 ION 0x0874 B 1 ION 0x0876 B 1 GeForce 9400 0x087A B 1 ION 0x087D B 1 ION LE 0x087E B 1 ION LE 0x087F B 1 GeForce GT 220 0x0A20 C GeForce 210 0x0A23 C GeForce GT 230M 0x0A28 C GeForce GT 330M 0x0A29 C GeForce GT 230M 0x0A2A C GeForce GT 330M 0x0A2B C GeForce GT 320M 0x0A2D C GeForce GT 240M 0x0A34 C GeForce GT 325M 0x0A35 C GeForce G210 0x0A60 C GeForce 205 0x0A62 C GeForce 310 0x0A63 C Second Generation ION 0x0A64 C GeForce 210 0x0A65 C GeForce 310 0x0A66 C GeForce G105M 0x0A68 B GeForce G105M 0x0A69 B GeForce 305M 0x0A6E C Second Generation ION 0x0A6F C GeForce 310M 0x0A70 C GeForce 305M 0x0A71 C GeForce 310M 0x0A72 C GeForce 305M 0x0A73 C GeForce G210M 0x0A74 C GeForce 310M 0x0A75 C GeForce GT 330 0x0CA0 A GeForce GT 320 0x0CA2 C GeForce GT 240 0x0CA3 C GeForce GT 340 0x0CA4 C GeForce GT 330 0x0CA7 A GeForce GTS 260M 0x0CA8 C GeForce GTS 250M 0x0CA9 C GeForce GT 335M 0x0CAF C GeForce GTS 350M 0x0CB0 C GeForce GTS 360M 0x0CB1 C A2. NVIDIA QUADRO GPUS NVIDIA GPU product Device PCI ID VDPAU features ---------------------------------- --------------- --------------- Quadro FX 4000 0x004E - Quadro FX 4500 0x009D - Quadro FX Go1400 0x00CC - Quadro FX 3450/4000 SDI 0x00CD - Quadro FX 1400 0x00CE - Quadro FX 3400/Quadro FX 4000 0x00F8 - Quadro NVS 440 0x014A - Quadro FX 540M 0x014C - Quadro FX 550 0x014D - Quadro FX 540 0x014E - Quadro NVS 285 0x0165 - Quadro FX 5600 0x019D - Quadro FX 4600 0x019E - Quadro NVS 110M 0x01DA - Quadro NVS 120M 0x01DB - Quadro FX 350M 0x01DC - Quadro FX 350 0x01DE - Quadro NVS 210S / GeForce 6150LE 0x0245 - Quadro NVS 510M 0x0299 - Quadro FX 2500M 0x029A - Quadro FX 1500M 0x029B - Quadro FX 5500 0x029C - Quadro FX 3500 0x029D - Quadro FX 1500 0x029E - Quadro FX 4500 X2 0x029F - Quadro FX 560M 0x039C - Quadro FX 560 0x039E - Quadro FX 370 0x040A A Quadro NVS 320M 0x040B A Quadro FX 570M 0x040C A Quadro FX 1600M 0x040D A Quadro FX 570 0x040E A Quadro FX 1700 0x040F A Quadro NVS 140M 0x0429 A Quadro NVS 130M 0x042A A Quadro NVS 135M 0x042B A Quadro FX 360M 0x042D A Quadro NVS 290 0x042F A Quadroplex 2200 D2 0x05ED A Quadroplex 2200 S4 0x05F8 A Quadro CX 0x05F9 A Quadro FX 5800 0x05FD A Quadro FX 4800 0x05FE A Quadro FX 3800 0x05FF A Quadro FX 4700 X2 0x0619 A Quadro FX 3700 0x061A A Quadro VX 200 0x061B A Quadro FX 3600M 0x061C A Quadro FX 2800M 0x061D A Quadro FX 3700M 0x061E A Quadro FX 3800M 0x061F A Quadro FX 1800 0x0638 A Quadro FX 2700M 0x063A A Quadro FX 380 0x0658 A Quadro FX 580 0x0659 A Quadro FX 1700M 0x065A A Quadro FX 770M 0x065C A Quadro NVS 150M 0x06EA B 1 Quadro NVS 160M 0x06EB B 1 Quadro NVS 420 0x06F8 B 1 Quadro FX 370 LP 0x06F9 B 1 Quadro NVS 450 0x06FA B 1 Quadro FX 370M 0x06FB B 1 Quadro NVS 295 0x06FD B 1 HICx16 + Graphics 0x06FF B 1 NVS 5100M 0x0A2C C Quadro FX 880M 0x0A3C C NVS 2100M 0x0A6A C NVS 3100M 0x0A6C C Quadro FX 380 LP 0x0A78 C Quadro FX 380M 0x0A7C C Quadro FX 1800M 0x0CBC C Below are the legacy GPUs that are no longer supported in the unified driver. These GPUs will continue to be maintained through the special legacy NVIDIA GPU driver releases. The 173.14.xx driver supports the following set of GPUs: NVIDIA GPU product Device PCI ID ---------------------------------- ---------------------------------- GeForce PCX 5750 0x00FA GeForce PCX 5900 0x00FB Quadro FX 330/GeForce PCX 5300 0x00FC Quadro FX 330/Quadro NVS 280 PCI-E 0x00FD Quadro FX 1300 0x00FE GeForce FX 5800 Ultra 0x0301 GeForce FX 5800 0x0302 Quadro FX 2000 0x0308 Quadro FX 1000 0x0309 GeForce FX 5600 Ultra 0x0311 GeForce FX 5600 0x0312 GeForce FX 5600XT 0x0314 GeForce FX Go5600 0x031A GeForce FX Go5650 0x031B Quadro FX Go700 0x031C GeForce FX 5200 0x0320 GeForce FX 5200 Ultra 0x0321 GeForce FX 5200 0x0322 GeForce FX 5200LE 0x0323 GeForce FX Go5200 0x0324 GeForce FX Go5250 0x0325 GeForce FX 5500 0x0326 GeForce FX 5100 0x0327 GeForce FX Go5200 32M/64M 0x0328 Quadro NVS 55/280 PCI 0x032A Quadro FX 500/FX 600 0x032B GeForce FX Go53xx 0x032C GeForce FX Go5100 0x032D GeForce FX 5900 Ultra 0x0330 GeForce FX 5900 0x0331 GeForce FX 5900XT 0x0332 GeForce FX 5950 Ultra 0x0333 GeForce FX 5900ZT 0x0334 Quadro FX 3000 0x0338 Quadro FX 700 0x033F GeForce FX 5700 Ultra 0x0341 GeForce FX 5700 0x0342 GeForce FX 5700LE 0x0343 GeForce FX 5700VE 0x0344 GeForce FX Go5700 0x0347 GeForce FX Go5700 0x0348 Quadro FX Go1000 0x034C Quadro FX 1100 0x034E The 96.43.xx driver supports the following set of GPUs: NVIDIA GPU product Device PCI ID ---------------------------------- ---------------------------------- GeForce2 MX/MX 400 0x0110 GeForce2 MX 100/200 0x0111 GeForce2 Go 0x0112 Quadro2 MXR/EX/Go 0x0113 GeForce4 MX 460 0x0170 GeForce4 MX 440 0x0171 GeForce4 MX 420 0x0172 GeForce4 MX 440-SE 0x0173 GeForce4 440 Go 0x0174 GeForce4 420 Go 0x0175 GeForce4 420 Go 32M 0x0176 GeForce4 460 Go 0x0177 Quadro4 550 XGL 0x0178 GeForce4 440 Go 64M 0x0179 Quadro NVS 400 0x017A Quadro4 500 GoGL 0x017C GeForce4 410 Go 16M 0x017D GeForce4 MX 440 with AGP8X 0x0181 GeForce4 MX 440SE with AGP8X 0x0182 GeForce4 MX 420 with AGP8X 0x0183 GeForce4 MX 4000 0x0185 Quadro4 580 XGL 0x0188 Quadro NVS 280 SD 0x018A Quadro4 380 XGL 0x018B Quadro NVS 50 PCI 0x018C GeForce2 Integrated GPU 0x01A0 GeForce4 MX Integrated GPU 0x01F0 GeForce3 0x0200 GeForce3 Ti 200 0x0201 GeForce3 Ti 500 0x0202 Quadro DCC 0x0203 GeForce4 Ti 4600 0x0250 GeForce4 Ti 4400 0x0251 GeForce4 Ti 4200 0x0253 Quadro4 900 XGL 0x0258 Quadro4 750 XGL 0x0259 Quadro4 700 XGL 0x025B GeForce4 Ti 4800 0x0280 GeForce4 Ti 4200 with AGP8X 0x0281 GeForce4 Ti 4800 SE 0x0282 GeForce4 4200 Go 0x0286 Quadro4 980 XGL 0x0288 Quadro4 780 XGL 0x0289 Quadro4 700 GoGL 0x028C The 71.86.xx driver supports the following set of GPUs: NVIDIA GPU product Device PCI ID ---------------------------------- ---------------------------------- RIVA TNT 0x0020 RIVA TNT2/TNT2 Pro 0x0028 RIVA TNT2 Ultra 0x0029 Vanta/Vanta LT 0x002C RIVA TNT2 Model 64/Model 64 Pro 0x002D Aladdin TNT2 0x00A0 GeForce 256 0x0100 GeForce DDR 0x0101 Quadro 0x0103 GeForce2 GTS/GeForce2 Pro 0x0150 GeForce2 Ti 0x0151 GeForce2 Ultra 0x0152 Quadro2 Pro 0x0153 ______________________________________________________________________________ Appendix B. X Config Options ______________________________________________________________________________ The following driver options are supported by the NVIDIA X driver. They may be specified either in the Screen or Device sections of the X config file. X Config Options Option "NvAGP" "integer" Configure AGP support. Integer argument can be one of: Value Behavior -------------- --------------------------------------------------- 0 disable AGP 1 use NVIDIA internal AGP support, if possible 2 use AGPGART, if possible 3 use any AGP support (try AGPGART, then NVIDIA AGP) Note that NVIDIA internal AGP support cannot work if AGPGART is either statically compiled into your kernel or is built as a module and loaded into your kernel. See Chapter 12 for details. Default: 3. Option "NoLogo" "boolean" Disable drawing of the NVIDIA logo splash screen at X startup. Default: the logo is drawn for screens with depth 24. Option "LogoPath" "string" Sets the path to the PNG file to be used as the logo splash screen at X startup. If the PNG file specified has a bKGD (background color) chunk, then the screen is cleared to the color it specifies. Otherwise, the screen is cleared to black. The logo file must be owned by root and must not be writable by a non-root group. Note that a logo is only displayed for screens with depth 24. Default: The built-in NVIDIA logo is used. Option "RenderAccel" "boolean" Enable or disable hardware acceleration of the RENDER extension. Default: hardware acceleration of the RENDER extension is enabled. Option "NoRenderExtension" "boolean" Disable the RENDER extension. Other than recompiling it, the X server does not seem to have another way of disabling this. Fortunately, we can control this from the driver so we export this option. This is useful in depth 8 where RENDER would normally steal most of the default colormap. Default: RENDER is offered when possible. Option "UBB" "boolean" Enable or disable the Unified Back Buffer on Quadro-based GPUs (Quadro NVS excluded); see Chapter 20 for a description of UBB. This option has no effect on non-Quadro GPU products. Default: UBB is on for Quadro GPUs. Option "NoFlip" "boolean" Disable OpenGL flipping; see Chapter 20 for a description. Default: OpenGL will swap by flipping when possible. Option "Dac8Bit" "boolean" Most Quadro products by default use a 10-bit color look-up table (LUT); setting this option to TRUE forces these GPUs to use an 8-bit (LUT). Default: a 10-bit LUT is used, when available. Option "Overlay" "boolean" Enables RGB workstation overlay visuals. This is only supported on Quadro GPUs (Quadro NVS GPUs excluded) in depth 24. This option causes the server to advertise the SERVER_OVERLAY_VISUALS root window property and GLX will report single- and double-buffered, Z-buffered 16-bit overlay visuals. The transparency key is pixel 0x0000 (hex). There is no gamma correction support in the overlay plane. This feature requires XFree86 version 4.2.0 or newer, or the X.Org X server. When the X screen is either wider than 2046 pixels or taller than 2047, the overlay may be emulated with a substantial performance penalty. RGB workstation overlays are not supported when the Composite extension is enabled. UBB must be enabled when overlays are enabled (this is the default behavior). Option "CIOverlay" "boolean" Enables Color Index workstation overlay visuals with identical restrictions to Option "Overlay" above. This option causes the server to advertise the SERVER_OVERLAY_VISUALS root window property. Some of the visuals advertised that way may be listed in the main plane (layer 0) for compatibility purposes. They however belong to the overlay (layer 1). The server will offer visuals both with and without a transparency key. These are depth 8 PseudoColor visuals. Enabling Color Index overlays on X servers older than XFree86 4.3 will force the RENDER extension to be disabled due to bugs in the RENDER extension in older X servers. Color Index workstation overlays are not supported when the Composite extension is enabled. Default: off. UBB must be enabled when overlays are enabled (this is the default behavior). Option "TransparentIndex" "integer" When color index overlays are enabled, use this option to choose which pixel is used for the transparent pixel in visuals featuring transparent pixels. This value is clamped between 0 and 255 (Note: some applications such as Alias's Maya require this to be zero in order to work correctly). Default: 0. Option "OverlayDefaultVisual" "boolean" When overlays are used, this option sets the default visual to an overlay visual thereby putting the root window in the overlay. This option is not recommended for RGB overlays. Default: off. Option "EmulatedOverlaysTimerMs" "integer" Enables the use of a timer within the X server to perform the updates to the emulated overlay or CI overlay. This option can be used to improve the performance of the emulated or CI overlays by reducing the frequency of the updates. The value specified indicates the desired number of milliseconds between overlay updates. To disable the use of the timer either leave the option unset or set it to 0. Default: off. Option "EmulatedOverlaysThreshold" "boolean" Enables the use of a threshold within the X server to perform the updates to the emulated overlay or CI overlay. The emulated or CI overlay updates can be deferred but this threshold will limit the number of deferred OpenGL updates allowed before the overlay is updated. This option can be used to trade off performance and animation quality. Default: on. Option "EmulatedOverlaysThresholdValue" "integer" Controls the threshold used in updating the emulated or CI overlays. This is used in conjunction with the EmulatedOverlaysThreshold option to trade off performance and animation quality. Higher values for this option favor performance over quality. Setting low values of this option will not cause the overlay to be updated more often than the frequence specified by the EmulatedOverlaysTimerMs option. Default: 5. Option "RandRRotation" "boolean" Enable rotation support for the XRandR extension. This allows use of the XRandR X server extension for configuring the screen orientation through rotation. This feature is supported using depth 24. This requires an X.Org X 6.8.1 or newer X server. This feature does not work with hardware overlays; emulated overlays will be used instead at a substantial performance penalty. See Chapter 17 for details. Default: off. Option "Rotate" "string" Enable static rotation support. Unlike the RandRRotation option above, this option takes effect as soon as the X server is started and will work with older versions of X. This feature is supported using depth 24. This feature does not work with hardware overlays; emulated overlays will be used instead at a substantial performance penalty. This option is not compatible with the RandR extension. Valid rotations are "normal", "left", "inverted", and "right". Default: off. Option "SWCursor" "boolean" Enable or disable software rendering of the X cursor. Default: off. Option "HWCursor" "boolean" Enable or disable hardware rendering of the X cursor. Default: on. Option "CursorShadow" "boolean" Enable or disable use of a shadow with the hardware accelerated cursor; this is a black translucent replica of your cursor shape at a given offset from the real cursor. Default: off (no cursor shadow). Option "CursorShadowAlpha" "integer" The alpha value to use for the cursor shadow; only applicable if CursorShadow is enabled. This value must be in the range [0, 255] -- 0 is completely transparent; 255 is completely opaque. Default: 64. Option "CursorShadowXOffset" "integer" The offset, in pixels, that the shadow image will be shifted to the right from the real cursor image; only applicable if CursorShadow is enabled. This value must be in the range [0, 32]. Default: 4. Option "CursorShadowYOffset" "integer" The offset, in pixels, that the shadow image will be shifted down from the real cursor image; only applicable if CursorShadow is enabled. This value must be in the range [0, 32]. Default: 2. Option "ConnectedMonitor" "string" Allows you to override what the NVIDIA kernel module detects is connected to your graphics card. This may be useful, for example, if you use a KVM (keyboard, video, mouse) switch and you are switched away when X is started. In such a situation, the NVIDIA kernel module cannot detect which display devices are connected, and the NVIDIA X driver assumes you have a single CRT. Valid values for this option are "CRT" (cathode ray tube), "DFP" (digital flat panel), or "TV" (television); if using TwinView, this option may be a comma-separated list of display devices; e.g.: "CRT, CRT" or "CRT, DFP". It is generally recommended to not use this option, but instead use the "UseDisplayDevice" option. NOTE: anything attached to a 15 pin VGA connector is regarded by the driver as a CRT. "DFP" should only be used to refer to digital flat panels connected via a DVI port. Default: string is NULL (the NVIDIA driver will detect the connected display devices). Option "UseDisplayDevice" "string" The "UseDisplayDevice" X configuration option is a list of one or more display devices, which limits the display devices the NVIDIA X driver will consider for an X screen. The display device names used in the option may be either specific (with a numeric suffix; e.g., "DFP-1") or general (without a numeric suffix; e.g., "DFP"). When assigning display devices to X screens, the NVIDIA X driver walks through the list of all (not already assigned) display devices detected as connected. When the "UseDisplayDevice" X configuration option is specified, the X driver will only consider connected display devices which are also included in the "UseDisplayDevice" list. This can be thought of as a "mask" against the connected (and not already assigned) display devices. Note the subtle difference between this option and the "ConnectedMonitor" option: the "ConnectedMonitor" option overrides which display devices are actually detected, while the "UseDisplayDevice" option controls which of the detected display devices will be used on this X screen. Of the list of display devices considered for this X screen (either all connected display devices, or a subset limited by the "UseDisplayDevice" option), the NVIDIA X driver first looks at CRTs, then at DFPs, and finally at TVs. For example, if both a CRT and a DFP are connected, by default the X driver would assign the CRT to this X screen. However, by specifying: Option "UseDisplayDevice" "DFP" the X screen would use the DFP instead. Or, if CRT-0, DFP-0, and DFP-1 are connected and TwinView is enabled, the X driver would assign CRT-0 and DFP-0 to the X screen. However, by specifying: Option "UseDisplayDevice" "CRT-0, DFP-1" the X screen would use CRT-0 and DFP-1 instead. Additionally, the special value "none" can be specified for the "UseDisplayDevice" option. When this value is given, any programming of the display hardware is disabled. The NVIDIA driver will not perform any mode validation or mode setting for this X screen. This is intended for use in conjunction with CUDA or in remote graphics solutions such as VNC or Hewlett Packard's Remote Graphics Software (RGS). This functionality is only available on Quadro and Tesla GPUs. Note the following restrictions for setting the "UseDisplayDevice" to "none": o OpenGL SyncToVBlank will have no effect. o None of Stereo, Overlay, CIOverlay, or SLI are allowed when "UseDisplayDevice" is set to "none". Option "UseEdidFreqs" "boolean" This option controls whether the NVIDIA X driver will use the HorizSync and VertRefresh ranges given in a display device's EDID, if any. When UseEdidFreqs is set to True, EDID-provided range information will override the HorizSync and VertRefresh ranges specified in the Monitor section. If a display device does not provide an EDID, or the EDID does not specify an hsync or vrefresh range, then the X server will default to the HorizSync and VertRefresh ranges specified in the Monitor section of your X config file. These frequency ranges are used when validating modes for your display device. Default: True (EDID frequencies will be used) Option "UseEDID" "boolean" By default, the NVIDIA X driver makes use of a display device's EDID, when available, during construction of its mode pool. The EDID is used as a source for possible modes, for valid frequency ranges, and for collecting data on the physical dimensions of the display device for computing the DPI (see Appendix E). However, if you wish to disable the driver's use of the EDID, you can set this option to False: Option "UseEDID" "FALSE" Note that, rather than globally disable all uses of the EDID, you can individually disable each particular use of the EDID; e.g., Option "UseEDIDFreqs" "FALSE" Option "UseEDIDDpi" "FALSE" Option "ModeValidation" "NoEdidModes" Default: True (use EDID). Option "UseInt10Module" "boolean" Enable use of the X Int10 module to soft-boot all secondary cards, rather than POSTing the cards through the NVIDIA kernel module. Default: off (POSTing is done through the NVIDIA kernel module). Option "TwinView" "boolean" Enable or disable TwinView. See Chapter 13 for details. Default: off (TwinView is disabled). Option "TwinViewOrientation" "string" Controls the relationship between the two display devices when using TwinView. Takes one of the following values: "RightOf" "LeftOf" "Above" "Below" "Clone". See Chapter 13 for details. Default: string is NULL. Option "SecondMonitorHorizSync" "range(s)" This option is like the HorizSync entry in the Monitor section, but is for the second monitor when using TwinView. See Chapter 13 for details. Default: none. Option "SecondMonitorVertRefresh" "range(s)" This option is like the VertRefresh entry in the Monitor section, but is for the second monitor when using TwinView. See Chapter 13 for details. Default: none. Option "MetaModes" "string" This option describes the combination of modes to use on each monitor when using TwinView or SLI Mosaic Mode. See Chapter 13 and Chapter 25 for details. Default: string is NULL. Option "NoTwinViewXineramaInfo" "boolean" When in TwinView, the NVIDIA X driver normally provides a Xinerama extension that X clients (such as window managers) can use to discover the current TwinView configuration, such as where each display device is positioned within the X screen. Some window mangers get confused by this information, so this option is provided to disable this behavior. Default: false (TwinView Xinerama information is provided). Due to bugs in some older software, TwinView Xinerama information is not provided by default on X.Org 7.1 and older when the X server is started with only one display device connected. Option "TwinViewXineramaInfoOrder" "string" When the NVIDIA X driver provides TwinViewXineramaInfo (see the NoTwinViewXineramaInfo X config option), it by default reports the currently enabled display devices in the order "CRT, DFP, TV". The TwinViewXineramaInfoOrder X config option can be used to override this order. The option string is a comma-separated list of display device names. The display device names can either be general (e.g, "CRT", which identifies all CRTs), or specific (e.g., "CRT-1", which identifies a particular CRT). Not all display devices need to be identified in the option string; display devices that are not listed will be implicitly appended to the end of the list, in their default order. Note that TwinViewXineramaInfoOrder tracks all display devices that could possibly be connected to the GPU, not just the ones that are currently enabled. When reporting the Xinerama information, the NVIDIA X driver walks through the display devices in the order specified, only reporting enabled display devices. Examples: "DFP" "TV, DFP" "DFP-1, DFP-0, TV, CRT" In the first example, any enabled DFPs would be reported first (any enabled CRTs or TVs would be reported afterwards). In the second example, any enabled TVs would be reported first, then any enabled DFPs (any enabled CRTs would be reported last). In the last example, if DFP-1 were enabled, it would be reported first, then DFP-0, then any enabled TVs, and then any enabled CRTs; finally, any other enabled DFPs would be reported. Default: "CRT, DFP, TV" Option "TwinViewXineramaInfoOverride" "string" This option overrides the values reported by NVIDIA's TwinView Xinerama implementation. This disregards the actual display devices used by the X screen and any order specified in TwinViewXineramaInfoOrder. The option string is interpreted as a comma-separated list of regions, specified as '[width]x[height]+[x-offset]+[y-offset]'. The regions' sizes and offsets are not validated against the X screen size, but are directly reported to any Xinerama client. Examples: "1600x1200+0+0, 1600x1200+1600+0" "1024x768+0+0, 1024x768+1024+0, 1024x768+0+768, 1024x768+1024+768" Option "TVStandard" "string" See Chapter 16 for details on configuring TV-out. Option "TVOutFormat" "string" See Chapter 16 for details on configuring TV-out. Option "TVOverScan" "Decimal value in the range 0.0 to 1.0" Valid values are in the range 0.0 through 1.0; See Chapter 16 for details on configuring TV-out. Option "Stereo" "integer" Enable offering of quad-buffered stereo visuals on Quadro. Integer indicates the type of stereo equipment being used: Value Equipment -------------- --------------------------------------------------- 1 DDC glasses. The sync signal is sent to the glasses via the DDC signal to the monitor. These usually involve a passthrough cable between the monitor and the graphics card. This mode is not available on G8xGL and higher GPUs. 2 "Blueline" glasses. These usually involve a passthrough cable between the monitor and graphics card. The glasses know which eye to display based on the length of a blue line visible at the bottom of the screen. When in this mode, the root window dimensions are one pixel shorter in the Y dimension than requested. This mode does not work with virtual root window sizes larger than the visible root window size (desktop panning). This mode is not available on G8xGL and higher GPUs. 3 Onboard stereo support. This is usually only found on professional cards. The glasses connect via a DIN connector on the back of the graphics card. 4 TwinView clone mode stereo (also known as "passive" stereo). On graphics cards that support TwinView, the left eye is displayed on the first display, and the right eye is displayed on the second display. This is normally used in conjunction with special projectors to produce 2 polarized images which are then viewed with polarized glasses. To use this stereo mode, you must also configure TwinView in clone mode with the same resolution, panning offset, and panning domains on each display. 5 Vertical interlaced stereo mode, for use with SeeReal Stereo Digital Flat Panels. 6 Color interleaved stereo mode, for use with Sharp3D Stereo Digital Flat Panels. 7 Horizontal interlaced stereo mode, for use with Arisawa, Hyundai, Zalman, Pavione, and Miracube Digital Flat Panels. 8 Checkerboard pattern stereo mode, for use with 3D DLP Display Devices. 9 Inverse checkerboard pattern stereo mode, for use with 3D DLP Display Devices. 10 NVIDIA 3D Vision mode for use with NVIDIA 3D Vision glasses. The NVIDIA 3D Vision infrared emitter must be connected to a USB port of your computer, and to the 3-pin DIN connector of a Quadro graphics board (based on G8xGL or higher GPU) before starting the X server. Hot-plugging the USB infrared stereo emitter is not yet supported. Also, 3D Vision Stereo Linux support requires a Linux kernel built with USB device filesystem (usbfs) and USB 2.0 support. Not presently supported on FreeBSD or Solaris. Stereo is only available on Quadro cards. Stereo options 1, 2, 3 and 10 (also known as "active" stereo) may be used with multiple display devices if all modes within each MetaMode have identical timing values. See Chapter 19 for suggestions on making sure the modes within your MetaModes are identical. The identical ModeLine requirement is not necessary for Stereo options 4 through 9 ("passive" stereo). Default: 0 (Stereo is not enabled). The following table summarize the available stereo modes, their supported GPUs, and their intended display devices. Stereo mode (value) Graphics card Display supported supported* -------------------- -------------------- -------------------- DDC glasses (1) Quadro graphics CRTs with high cards with refresh rate pre-G8xGL GPUs Blueline glasses Quadro graphics CRTs with high (2) cards with refresh rate pre-G8xGL GPUs Onboard DIN (3) Quadro graphics Displays with high cards refresh rate TwinView clone (4) Quadro graphics Any stereo display cards device with two inputs Vertical Interlaced Quadro graphics SeeReal Stereo DFP (5) cards Color Interleaved Quadro graphics Sharp3D stereo DFP (6) cards Horizontal Quadro graphics Arisawa, Hyundai, Interlaced (7) cards# Zalman, Pavione, and Miracube Checkerboard Quadro graphics 3D DLP display Pattern (8) cards# devices Inverse Quadro graphics 3D DLP display Checkerboard (9) cards# devices NVIDIA 3D Vision Quadro graphics Supported 3D Vision (10) cards with G8xGL or ready displays^ higher GPU# * Quadro graphics cards excluding Quadro NVS cards. # http://www.nvidia.com/object/quadro_pro_graphics_boards.html ^ http://www.nvidia.com/object/3D_Vision_Requirements.html UBB must be enabled when stereo is enabled (this is the default behavior). Stereo options 1, 2, and 3 ("active" stereo) can be enabled on digital display devices (connected via DVI, HDMI, or DisplayPort). However, some digital display devices might not behave as desired with active stereo: o Some digital display devices may not be able to toggle pixel colors quickly enough when flipping between eyes on every vblank. o Some digital display devices may have an optical polarization that interferes with stereo goggles. o Active stereo requires high refresh rates, because a vertical refresh is needed to display each eye. Some digital display devices have a low refresh rate, which will result in flickering when used for active stereo. o Some digital display devices might internally convert from other refresh rates to their native refresh rate (e.g., 60Hz), resulting in incompatible rates between the stereo glasses and stereo displayed on screen. Stereo applies to an entire X screen, so it will apply to all display devices on that X screen, whether or not they all support the selected Stereo mode. Stereo options 7, 8, 9, and 10 are only supported on G8xGL and higher GPUs. Multi-GPU cards (such as the Quadro FX 4500 X2) provide a single DIN connector for onboard stereo support (option 3) and NVIDIA 3D Vision stereo (option 10), which is tied to the bottommost GPU. In order to synchronize stereo with the other GPU, you must use a G-Sync device (see Chapter 26 for details). Option "ForceStereoFlipping" "boolean" Stereo flipping is the process by which left and right eyes are displayed on alternating vertical refreshes. Normally, stereo flipping is only performed when a stereo drawable is visible. This option forces stereo flipping even when no stereo drawables are visible. This is to be used in conjunction with the "Stereo" option. If "Stereo" is 0, the "ForceStereoFlipping" option has no effect. If otherwise, the "ForceStereoFlipping" option will force the behavior indicated by the "Stereo" option, even if no stereo drawables are visible. This option is useful in a multiple-screen environment in which a stereo application is run on a different screen than the stereo master. Possible values: Value Behavior -------------- --------------------------------------------------- 0 Stereo flipping is not forced. The default behavior as indicated by the "Stereo" option is used. 1 Stereo flipping is forced. Stereo is running even if no stereo drawables are visible. The stereo mode depends on the value of the "Stereo" option. Default: 0 (Stereo flipping is not forced). Note that active stereo is not supported on digital flat panels. Option "XineramaStereoFlipping" "boolean" By default, when using Stereo with Xinerama, all physical X screens having a visible stereo drawable will stereo flip. Use this option to allow only one physical X screen to stereo flip at a time. This is to be used in conjunction with the "Stereo" and "Xinerama" options. If "Stereo" is 0 or "Xinerama" is 0, the "XineramaStereoFlipping" option has no effect. If you wish to have all X screens stereo flip all the time, see the "ForceStereoFlipping" option. Possible values: Value Behavior -------------- --------------------------------------------------- 0 Stereo flipping is enabled on one X screen at a time. Stereo is enabled on the first X screen having the stereo drawable. 1 Stereo flipping in enabled on all X screens. Default: 1 (Stereo flipping is enabled on all X screens). Option "IgnoreDisplayDevices" "string" This option tells the NVIDIA kernel module to completely ignore the indicated classes of display devices when checking which display devices are connected. You may specify a comma-separated list containing any of "CRT", "DFP", and "TV". For example: Option "IgnoreDisplayDevices" "DFP, TV" will cause the NVIDIA driver to not attempt to detect if any digital flat panels or TVs are connected. This option is not normally necessary; however, some video BIOSes contain incorrect information about which display devices may be connected, or which i2c port should be used for detection. These errors can cause long delays in starting X. If you are experiencing such delays, you may be able to avoid this by telling the NVIDIA driver to ignore display devices which you know are not connected. NOTE: anything attached to a 15 pin VGA connector is regarded by the driver as a CRT. "DFP" should only be used to refer to digital flat panels connected via a DVI port. Option "MultisampleCompatibility" "boolean" Enable or disable the use of separate front and back multisample buffers. Enabling this will consume more memory but is necessary for correct output when rendering to both the front and back buffers of a multisample or FSAA drawable. This option is necessary for correct operation of SoftImage XSI. Default: false (a single multisample buffer is shared between the front and back buffers). Option "NoPowerConnectorCheck" "boolean" The NVIDIA X driver will fail initialization on a GPU if it detects that the GPU that requires an external power connector does not have an external power connector plugged in. This option can be used to bypass this test. Default: false (the power connector test is performed). Option "ThermalConfigurationCheck" "boolean" The NVIDIA X driver will fail initialization on a GPU if it detects that the GPU has a bad thermal configuration. This may indicate a problem with how your graphics board was built, or simply a driver bug. It is recommended that you contact your graphics board vendor if you encounter this problem. This option can be set to False to bypass this test. Default: true (the thermal configuration test is performed). Option "XvmcUsesTextures" "boolean" Forces XvMC to use the 3D engine for XvMCPutSurface requests rather than the video overlay. Default: false (video overlay is used when available). Option "AllowGLXWithComposite" "boolean" Enables GLX even when the Composite X extension is loaded. ENABLE AT YOUR OWN RISK. OpenGL applications will not display correctly in many circumstances with this setting enabled. This option is intended for use on X.Org X servers older than X11R6.9.0. On X11R6.9.0 or newer X servers, the NVIDIA OpenGL implementation interacts properly by default with the Composite X extension and this option should not be needed. However, on X11R6.9.0 or newer X servers, support for GLX with Composite can be disabled by setting this option to False. Default: false (GLX is disabled when Composite is enabled on X servers older than X11R6.9.0). Option "UseCompositeWrapper" "boolean" Enables the X server's "composite wrapper", which performs coordinate translations necessary for the Composite extension. Default: false (the NVIDIA X driver performs its own coordinate translation). Option "AddARGBGLXVisuals" "boolean" Adds a 32-bit ARGB visual for each supported OpenGL configuration. This allows applications to use OpenGL to render with alpha transparency into 32-bit windows and pixmaps. This option requires the Composite extension. Default: ARGB GLX visuals are enabled on X servers new enough to support them when the Composite extension is also enabled and the screen depth is 24 or 30. Option "DisableGLXRootClipping" "boolean" If enabled, no clipping will be performed on rendering done by OpenGL in the root window. This option is deprecated. It is needed by older versions of OpenGL-based composite managers that draw the contents of redirected windows directly into the root window using OpenGL. Most OpenGL-based composite managers have been updated to support the Composite Overlay Window, a feature introduced in Xorg release 7.1. Using the Composite Overlay Window is the preferred method for performing OpenGL-based compositing. Option "DamageEvents" "boolean" Use OS-level events to efficiently notify X when a client has performed direct rendering to a window that needs to be composited. This will significantly improve performance and interactivity when using GLX applications with a composite manager running. It will also affect applications using GLX when rotation is enabled. This option is currently incompatible with SLI and Multi-GPU modes and will be disabled if either are used. Enabled by default. Option "ExactModeTimingsDVI" "boolean" Forces the initialization of the X server with the exact timings specified in the ModeLine. Default: false (for DVI devices, the X server initializes with the closest mode in the EDID list). Option "Coolbits" "integer" Enables various unsupported features, such as support for GPU clock manipulation in the NV-CONTROL X extension. This option accepts a bit mask of features to enable. WARNING: this may cause system damage and void warranties. This utility can run your computer system out of the manufacturer's design specifications, including, but not limited to: higher system voltages, above normal temperatures, excessive frequencies, and changes to BIOS that may corrupt the BIOS. Your computer's operating system may hang and result in data loss or corrupted images. Depending on the manufacturer of your computer system, the computer system, hardware and software warranties may be voided, and you may not receive any further manufacturer support. NVIDIA does not provide customer service support for the Coolbits option. It is for these reasons that absolutely no warranty or guarantee is either express or implied. Before enabling and using, you should determine the suitability of the utility for your intended use, and you shall assume all responsibility in connection therewith. When "1" (Bit 0) is set in the "Coolbits" option value, the nvidia-settings utility will contain a page labeled "Clock Frequencies" through which clock settings can be manipulated. On mobile GPUs, limited clock manipulation support is available when "1" is set in the "Coolbits" option value: clocks can be lowered relative to the default settings, but overclocking is not supported due to the thermal constraints of notebook designs. When "2" (Bit 1) is set in the "Coolbits" option value, the NVIDIA driver will attempt to initialize SLI when using GPUs with different amounts of video memory. When "4" (Bit 2) is set in the "Coolbits" option value, the nvidia-settings Thermal Monitor page will allow configuration of GPU fan speed, on graphics boards with programmable fan capability. The default for this option is 0 (unsupported features are disabled). Option "MultiGPU" "string" This option controls the configuration of Multi-GPU rendering in supported configurations. Value Behavior -------------------------------- -------------------------------- 0, no, off, false, Single Use only a single GPU when rendering 1, yes, on, true, Auto Enable Multi-GPU and allow the driver to automatically select the appropriate rendering mode. AFR Enable Multi-GPU and use the Alternate Frame Rendering mode. SFR Enable Multi-GPU and use the Split Frame Rendering mode. AA Enable Multi-GPU and use antialiasing. Use this in conjunction with full scene antialiasing to improve visual quality. Option "SLI" "string" This option controls the configuration of SLI rendering in supported configurations. Value Behavior -------------------------------- -------------------------------- 0, no, off, false, Single Use only a single GPU when rendering 1, yes, on, true, Auto Enable SLI and allow the driver to automatically select the appropriate rendering mode. AFR Enable SLI and use the Alternate Frame Rendering mode. SFR Enable SLI and use the Split Frame Rendering mode. AA Enable SLI and use SLI Antialiasing. Use this in conjunction with full scene antialiasing to improve visual quality. AFRofAA Enable SLI and use SLI Alternate Frame Rendering of Antialiasing mode. Use this in conjunction with full scene antialiasing to improve visual quality. This option is only valid for SLI configurations with 4 GPUs. Mosaic Enable SLI and use SLI Mosaic Mode. Use this in conjunction with the MetaModes X configuration option to specify the combination of mode(s) used on each display. Option "TripleBuffer" "boolean" Enable or disable the use of triple buffering. If this option is enabled, OpenGL windows that sync to vblank and are double-buffered will be given a third buffer. This decreases the time an application stalls while waiting for vblank events, but increases latency slightly (delay between user input and displayed result). Option "DPI" "string" This option specifies the Dots Per Inch for the X screen; for example: Option "DPI" "75 x 85" will set the horizontal DPI to 75 and the vertical DPI to 85. By default, the X driver will compute the DPI of the X screen from the EDID of any connected display devices. See Appendix E for details. Default: string is NULL (disabled). Option "UseEdidDpi" "string" By default, the NVIDIA X driver computes the DPI of an X screen based on the physical size of the display device, as reported in the EDID, and the size in pixels of the first mode to be used on the display device. If multiple display devices are used by the X screen, then the NVIDIA X screen will choose which display device to use. This option can be used to specify which display device to use. The string argument can be a display device name, such as: Option "UseEdidDpi" "DFP-0" or the argument can be "FALSE" to disable use of EDID-based DPI calculations: Option "UseEdidDpi" "FALSE" See Appendix E for details. Default: string is NULL (the driver computes the DPI from the EDID of a display device and selects the display device). Option "ConstantDPI" "boolean" By default on X.Org 6.9 or newer X servers, the NVIDIA X driver recomputes the size in millimeters of the X screen whenever the size in pixels of the X screen is changed using XRandR, such that the DPI remains constant. This behavior can be disabled (which means that the size in millimeters will not change when the size in pixels of the X screen changes) by setting the "ConstantDPI" option to "FALSE"; e.g., Option "ConstantDPI" "FALSE" ConstantDPI defaults to True. On X servers older than X.Org 6.9, the NVIDIA X driver cannot change the size in millimeters of the X screen. Therefore the DPI of the X screen will change when XRandR changes the size in pixels of the X screen. The driver will behave as if ConstantDPI was forced to FALSE. Option "CustomEDID" "string" This option forces the X driver to use the EDID specified in a file rather than the display's EDID. You may specify a semicolon separated list of display names and filename pairs. Valid display device names include "CRT-0", "CRT-1", "DFP-0", "DFP-1", "TV-0", "TV-1", or one of the generic names "CRT", "DFP", "TV", which apply the EDID to all devices of the specified type. Additionally, if SLI Mosaic is enabled, this name can be prefixed by a GPU name (e.g., "GPU-0.CRT-0"). The file contains a raw EDID (e.g., a file generated by nvidia-settings). For example: Option "CustomEDID" "CRT-0:/tmp/edid1.bin; DFP-0:/tmp/edid2.bin" will assign the EDID from the file /tmp/edid1.bin to the display device CRT-0, and the EDID from the file /tmp/edid2.bin to the display device DFP-0. Note that a display device name must always be specified even if only one EDID is specified. Caution: Specifying an EDID that doesn't exactly match your display may damage your hardware, as it allows the driver to specify timings beyond the capabilities of your display. Use with care. Option "IgnoreEDIDChecksum" "string" This option forces the X driver to accept an EDID even if the checksum is invalid. You may specify a comma separated list of display names. Valid display device names include "CRT-0", "CRT-1", "DFP-0", "DFP-1", "TV-0", "TV-1", or one of the generic names "CRT", "DFP", "TV", which ignore the EDID checksum on all devices of the specified type. Additionally, if SLI Mosaic is enabled, this name can be prefixed by a GPU name (e.g., "GPU-0.CRT-0"). For example: Option "IgnoreEDIDChecksum" "CRT, DFP-0" will cause the nvidia driver to ignore the EDID checksum for all CRT monitors and the displays DFP-0 and TV-0. Caution: An invalid EDID checksum may indicate a corrupt EDID. A corrupt EDID may have mode timings beyond the capabilities of your display, and using it could damage your hardware. Use with care. Option "ModeValidation" "string" This option provides fine-grained control over each stage of the mode validation pipeline, disabling individual mode validation checks. This option should only very rarely be used. The option string is a semicolon-separated list of comma-separated lists of mode validation arguments. Each list of mode validation arguments can optionally be prepended with a display device name and GPU specifier. ": , ; : , , ; ..." Possible arguments: o "AllowNon60HzDFPModes": some lower quality TMDS encoders are only rated to drive DFPs at 60Hz; the driver will determine when only 60Hz DFP modes are allowed. This argument disables this stage of the mode validation pipeline. o "NoMaxPClkCheck": each mode has a pixel clock; this pixel clock is validated against the maximum pixel clock of the hardware (for a DFP, this is the maximum pixel clock of the TMDS encoder, for a CRT, this is the maximum pixel clock of the DAC). This argument disables the maximum pixel clock checking stage of the mode validation pipeline. o "NoEdidMaxPClkCheck": a display device's EDID can specify the maximum pixel clock that the display device supports; a mode's pixel clock is validated against this pixel clock maximum. This argument disables this stage of the mode validation pipeline. o "AllowInterlacedModes": interlaced modes are not supported on all NVIDIA GPUs; the driver will discard interlaced modes on GPUs where interlaced modes are not supported; this argument disables this stage of the mode validation pipeline. o "NoMaxSizeCheck": each NVIDIA GPU has a maximum resolution that it can drive; this argument disables this stage of the mode validation pipeline. o "NoHorizSyncCheck": a mode's horizontal sync is validated against the range of valid horizontal sync values; this argument disables this stage of the mode validation pipeline. o "NoVertRefreshCheck": a mode's vertical refresh rate is validated against the range of valid vertical refresh rate values; this argument disables this stage of the mode validation pipeline. o "NoWidthAlignmentCheck": the alignment of a mode's visible width is validated against the capabilities of the GPU; normally, a mode's visible width must be a multiple of 8. This argument disables this stage of the mode validation pipeline. o "NoDFPNativeResolutionCheck": when validating for a DFP, a mode's size is validated against the native resolution of the DFP; this argument disables this stage of the mode validation pipeline. o "NoVirtualSizeCheck": if the X configuration file requests a specific virtual screen size, a mode cannot be larger than that virtual size; this argument disables this stage of the mode validation pipeline. o "NoVesaModes": when constructing the mode pool for a display device, the X driver uses a built-in list of VESA modes as one of the mode sources; this argument disables use of these built-in VESA modes. o "NoEdidModes": when constructing the mode pool for a display device, the X driver uses any modes listed in the display device's EDID as one of the mode sources; this argument disables use of EDID-specified modes. o "NoXServerModes": when constructing the mode pool for a display device, the X driver uses the built-in modes provided by the core XFree86/Xorg X server as one of the mode sources; this argument disables use of these modes. Note that this argument does not disable custom ModeLines specified in the X config file; see the "NoCustomModes" argument for that. o "NoCustomModes": when constructing the mode pool for a display device, the X driver uses custom ModeLines specified in the X config file (through the "Mode" or "ModeLine" entries in the Monitor Section) as one of the mode sources; this argument disables use of these modes. o "NoPredefinedModes": when constructing the mode pool for a display device, the X driver uses additional modes predefined by the NVIDIA X driver; this argument disables use of these modes. o "NoUserModes": additional modes can be added to the mode pool dynamically, using the NV-CONTROL X extension; this argument prohibits user-specified modes via the NV-CONTROL X extension. o "NoExtendedGpuCapabilitiesCheck": allow mode timings that may exceed the GPU's extended capability checks. o "ObeyEdidContradictions": an EDID may contradict itself by listing a mode as supported, but the mode may exceed an EDID-specified valid frequency range (HorizSync, VertRefresh, or maximum pixel clock). Normally, the NVIDIA X driver prints a warning in this scenario, but does not invalidate an EDID-specified mode just because it exceeds an EDID-specified valid frequency range. However, the "ObeyEdidContradictions" argument instructs the NVIDIA X driver to invalidate these modes. o "NoTotalSizeCheck": allow modes in which the individual visible or sync pulse timings exceed the total raster size. o "DoubleScanPriority": on GPUs older than G80, doublescan modes are sorted before non-doublescan modes of the same resolution for purposes of mode pool sorting; but on G80 and later GPUs, doublescan modes are sorted after non-doublescan modes of the same resolution. This token inverts that priority (i.e., doublescan modes will be sorted after on pre-G80 GPUs, and sorted before on G80 and later GPUs). o "NoDualLinkDVICheck": for mode timings used on dual link DVI DFPs, the driver must perform additional checks to ensure that the correct pixels are sent on the correct link. For some of these checks, the driver will invalidate the mode timings; for other checks, the driver will implicitly modify the mode timings to meet the GPU's dual link DVI requirements. This token disables this dual link DVI checking. o "NoDisplayPortBandwidthCheck": for mode timings used on DisplayPort devices, the driver must verify that the DisplayPort link can be configured to carry enough bandwidth to support a given mode's pixel clock. For example, some DisplayPort-to-VGA adapters only support 2 DisplayPort lanes, limiting the resolutions they can display. This token disables this DisplayPort bandwidth check. Examples: Option "ModeValidation" "NoMaxPClkCheck" disable the maximum pixel clock check when validating modes on all display devices. Option "ModeValidation" "CRT-0: NoEdidModes, NoMaxPClkCheck; GPU-0.DFP-0: NoVesaModes" do not use EDID modes and do not perform the maximum pixel clock check on CRT-0, and do not use VESA modes on DFP-0 of GPU-0. Option "ModeDebug" "boolean" This option causes the X driver to print verbose details about mode validation to the X log file. Note that this option is applied globally: setting this option to TRUE will enable verbose mode validation logging for all NVIDIA X screens in the X server. Option "UseEvents" "boolean" Enables the use of system events in some cases when the X driver is waiting for the hardware. The X driver can briefly spin through a tight loop when waiting for the hardware. With this option the X driver instead sets an event handler and waits for the hardware through the 'poll()' system call. Default: the use of the events is disabled. Option "FlatPanelProperties" "string" This option requests particular properties for all or a subset of the connected flat panels. The option string is a semicolon-separated list of comma-separated property=value pairs. Each list of property=value pairs can optionally be prepended with a flat panel name and GPU specifier. ": , ; : ; ..." Recognized properties: o "Scaling": controls the flat panel scaling mode; possible values are: 'Default' (the driver will use whichever scaling state is current), 'Native' (the driver will use the flat panel's scaler, if possible), 'Scaled' (the driver will use the NVIDIA GPU's scaler, if possible), 'Centered' (the driver will center the image, if possible), and 'aspect-scaled' (the X driver will scale with the NVIDIA GPU's scaler, but keep the aspect ratio correct). o "Dithering": controls the flat panel dithering mode; possible values are: 'Default' (the driver will decide when to dither), 'Enabled' (the driver will always dither, if possible), and 'Disabled' (the driver will never dither). Examples: Option "FlatPanelProperties" "Scaling = Centered" set the flat panel scaling mode to centered on all flat panels. Option "FlatPanelProperties" "GPU-0.DFP-0: Scaling = Centered; DFP-1: Scaling = Scaled, Dithering = Enabled" set the scaling mode of DFP-0 on GPU-0 to centered, set DFP-1's scaling mode to scaled and its dithering mode to enabled. Option "ProbeAllGpus" "boolean" When the NVIDIA X driver initializes, it probes all GPUs in the system, even if no X screens are configured on them. This is done so that the X driver can report information about all the system's GPUs through the NV-CONTROL X extension. This option can be set to FALSE to disable this behavior, such that only GPUs with X screens configured on them will be probed. Default: all GPUs in the system are probed. Option "DynamicTwinView" "boolean" Enable or disable support for dynamically configuring TwinView on this X screen. When DynamicTwinView is enabled (the default), the refresh rate of a mode (reported through XF86VidMode or XRandR) does not correctly report the refresh rate, but instead is a unique number such that each MetaMode has a different value. This is to guarantee that MetaModes can be uniquely identified by XRandR. When DynamicTwinView is disabled, the refresh rate reported through XRandR will be accurate, but NV-CONTROL clients such as nvidia-settings will not be able to dynamically manipulate the X screen's MetaModes. TwinView can still be configured from the X config file when DynamicTwinView is disabled. Default: DynamicTwinView is enabled. Option "IncludeImplicitMetaModes" "boolean" When the X server starts, a mode pool is created per display device, containing all the mode timings that the NVIDIA X driver determined to be valid for the display device. However, the only MetaModes that are made available to the X server are the ones explicitly requested in the X configuration file. It is convenient for fullscreen applications to be able to change between the modes in the mode pool, even if a given target mode was not explicitly requested in the X configuration file. To facilitate this, the NVIDIA X driver will, if only one display device is in use when the X server starts, implicitly add MetaModes for all modes in the display device's mode pool. This makes all the modes in the mode pool available to full screen applications that use the XF86VidMode or XRandR X extensions. To prevent this behavior, and only add MetaModes that are explicitly requested in the X configuration file, set this option to FALSE. Default: IncludeImplicitMetaModes is enabled. Option "IndirectMemoryAccess" "boolean" Some graphics cards have more video memory than can be mapped at once by the CPU (generally at most 256 MB of video memory can be CPU-mapped). On graphics cards based on G80 and higher, this option allows the driver to: o place more pixmaps in video memory, which will improve hardware rendering performance but may slow down software rendering; o allocate buffers larger than 256 MB, which is necessary to reach the maximum buffer size on newer GPUs. On some systems, up to 3 gigabytes of virtual address space may be reserved in the X server for indirect memory access. This virtual memory does not consume any physical resources. Note that the amount of reserved memory may be limited on 32-bit platforms, so some problems with large buffer allocations can be resolved by switching to a 64-bit operating system. Default: on (indirect memory access will be used, when available). Option "OnDemandVBlankInterrupts" "boolean" Normally, VBlank interrupts are generated on every vertical refresh of every display device connected to the GPU(s) installed in a given system. This experimental option enables on-demand VBlank control, allowing the driver to enable VBlank interrupt generation only when it is required. This can help conserve power. Default: off (on-demand VBlank control is disabled). Option "PixmapCacheSize" "size" This option controls how much video memory is reserved for pixmap allocations. When the option is specified, "size" specifies the number of bytes to use for the pixmap cache. Reserving this memory improves performance when pixmaps are created and destroyed rapidly, but prevents this memory from being used by OpenGL. When this cache is disabled or space in the cache is exhausted, the driver will still allocate pixmaps in video memory but pixmap creation and deletion performance will not be improved. NOTE: This option is deprecated in favor of the PixmapCacheRoundSizeKB nvidia-settings attribute and will be removed in a future driver release. Example: "Option "PixmapCacheSize" "1048576"" will allocate one megabyte for the pixmap cache. Default: off (no memory is reserved specifically for pixmaps). Option "AllowSHMPixmaps" "boolean" This option controls whether applications can use the MIT-SHM X extension to create pixmaps whose contents are shared between the X server and the client. These pixmaps prevent the NVIDIA driver from performing a number of optimizations and degrade performance in many circumstances. Disabling this option disables only shared memory pixmaps. Applications can still use the MIT-SHM extension to transfer data to the X server through shared memory using XShmPutImage. Default: off (shared memory pixmaps are not allowed). Option "InitializeWindowBackingPixmaps" "boolean" This option controls whether the NVIDIA X Driver initializes newly created redirected windows using the contents of their parent window if the X server doesn't do it. Leaving redirected windows uninitialized may cause new windows to flash with black or random colors when some compositing managers are running. This option will have no effect on X servers that already initialize redirected window contents. In most distributions, the X server is patched to skip that initialization. In this case, it is recommended to leave this option on for a better user experience. Default: on (redirected windows are initialized). Option "AllowUnofficialGLXProtocol" "boolean" By default, the NVIDIA GLX implementation will not expose GLX protocol for GL commands if the protocol is not considered complete. Protocol could be considered incomplete for a number of reasons. The implementation could still be under development and contain known bugs, or the protocol specification itself could be under development or going through review. If users would like to test the server-side portion of such protocol when using indirect rendering, they can enable this option. If any X screen enables this option, it will enable protocol on all screens in the server. When an NVIDIA GLX client is used, the related environment variable "__GL_ALLOW_UNOFFICIAL_PROTOCOL" will need to be set as well to enable support in the client. Option "PanAllDisplays" "boolean" When this option is enabled, all displays in the current MetaMode will pan as the pointer is moved. If disabled, only the displays whose panning domain contains the pointer (at its new location) are panned. Default: enabled (all displays are panned when the pointer is moved). Option "GvoDataFormat" "string" This option controls the initial configuration of SDI (GVO) device's output data format. Valid Values --------------------------------------------------------------------- R8G8B8_To_YCrCb444 R8G8B8_To_YCrCb422 X8X8X8_To_PassThru444 Default: R8G8B8_To_YCrCb444. Option "GvoSyncMode" "string" This option controls the initial synchronization mode of the SDI (GVO) device. Value Behavior -------------- --------------------------------------------------- FreeRunning The SDI output will be synchronized with the timing chosen from the SDI signal format list. GenLock SDI output will be synchronized with the external sync signal (if present/detected) with pixel accuracy. FrameLock SDI output will be synchronized with the external sync signal (if present/detected) with frame accuracy. Default: FreeRunning (Will not lock to an input signal). Option "GvoSyncSource" "string" This option controls the initial synchronization source (type) of the SDI (GVO) device. Note that the GvoSyncMode should be set to either GenLock or FrameLock for this option to take effect. Value Behavior -------------- --------------------------------------------------- Composite Interpret sync source as composite. SDI Interpret sync source as SDI. Default: SDI. Option "ConnectToAcpid" "boolean" The ACPI daemon (acpid) receives information about ACPI events like AC/Battery power, docking, etc. acpid will deliver these events to the NVIDIA X driver via a UNIX domain socket connection. By default, the NVIDIA X driver will attempt to connect to acpid to receive these events. Set this option to "off" to prevent the NVIDIA X driver from connecting to acpid. Default: on (the NVIDIA X driver will attempt to connect to acpid). Option "AcpidSocketPath" "string" The NVIDIA X driver attempts to connect to the ACPI daemon (acpid) via a UNIX domain socket. The default path to this socket is "/var/run/acpid.socket". Set this option to specify an alternate path to acpid's socket. Default: "/var/run/acpid.socket". Option "EnableACPIHotkeys" "boolean" The NVIDIA Linux X driver can detect mobile display change hotkey events either through ACPI or by periodically checking the GPU hardware state. While checking the GPU hardware state is generally sufficient to detect display change hotkey events, ACPI hotkey event delivery is preferable. However, X servers prior to X.Org xserver-1.2.0 have a bug that cause the X server to crash when the X server receives an ACPI hotkey event (freedesktop.org bug 8776). The NVIDIA Linux X driver will key off the X server ABI version to determine if the X server in use has this bug (X servers with ABI 1.1 or later do not). Since some X servers may have an earlier ABI but have a patch to fix the bug, the "EnableACPIHotkeys" option can be specified to override the NVIDIA X driver's default decision to enable or disable ACPI display change hotkey events. When running on a mobile system, search for "ACPI display change hotkey events" in your X log to see the NVIDIA X driver's decision. Default: the NVIDIA X driver will decide whether to enable ACPI display change hotkey events based on the X server ABI. Option "EnableACPIBrightnessHotkeys" "boolean" Enable or disable handling of ACPI brightness change hotkey events. Default: enabled ______________________________________________________________________________ Appendix C. Display Device Names ______________________________________________________________________________ A "display device" refers to some piece of hardware capable of displaying an image. There are three categories of display devices: analog displays (i.e., CRTs), digital displays (i.e., digital flat panels (DFPs)), and televisions. Note that analog flat panels are considered the same as analog CRTs by the NVIDIA Linux driver. A "display device name" is a string description that uniquely identifies a display device; it follows the format "-", for example: "CRT-0", "CRT-1", "DFP-0", or "TV-0". Note that the number indicates how the display device connector is wired on the graphics card, and has nothing to do with how many of that kind of display device are present. This means, for example, that you may have a "CRT-1", even if you do not have a "CRT-0". To determine which display devices are currently connected, you may check your X log file for a line similar to the following: (II) NVIDIA(0): Connected display device(s): CRT-0, DFP-0 Display device names can be used in the MetaMode, HorizSync, and VertRefresh X config options to indicate which display device a setting should be applied to. For example: Option "MetaModes" "CRT-0: 1600x1200, DFP-0: 1024x768" Option "HorizSync" "CRT-0: 50-110; DFP-0: 40-70" Option "VertRefresh" "CRT-0: 60-120; DFP-0: 60" Specifying the display device name in these options is not required; if display device names are not specified, then the driver attempts to infer which display device a setting applies to. In the case of MetaModes, for example, the first mode listed is applied to the "first" display device, and the second mode listed is applied to the "second" display device. Unfortunately, it is often unclear which display device is the "first" or "second". That is why specifying the display device name is preferable. When specifying display device names, you may also omit the number part of the name, though this is only useful if you only have one of that type of display device. For example, if you have one CRT and one DFP connected, you may reference them in the MetaMode string as follows: Option "MetaModes" "CRT: 1600x1200, DFP: 1024x768" If multiple matches on a single display device are possible, the driver attempts to match an exact display device, then a display device type, then any valid entry. For example: Option "HorizSync" "CRT-0: 60-120, CRT: 60" would match CRT-0 to the first entry, and CRT-1 to the second entry. In SLI Mosaic Mode, it may be possible for the same name to be used for multiple display devices connected to different GPUs. In order to distinguish between these devices, you can prefix them with a GPU qualifier. For example: Option "MetaModes" "GPU-0.CRT-0: 1600x1200, GPU-1.CRT-0: 1024x768" If no GPU is specified for a particular display device name, the setting will apply to any devices with that name across all GPUs. ______________________________________________________________________________ Appendix D. GLX Support ______________________________________________________________________________ This release supports GLX 1.4. Additionally, the following GLX extensions are supported on appropriate GPUs: o GLX_EXT_visual_info o GLX_EXT_visual_rating o GLX_SGIX_fbconfig o GLX_SGIX_pbuffer o GLX_ARB_get_proc_address o GLX_SGI_video_sync o GLX_SGI_swap_control o GLX_ARB_multisample o GLX_NV_float_buffer o GLX_ARB_fbconfig_float o GLX_NV_swap_group o GLX_NV_video_out o GLX_EXT_texture_from_pixmap o GLX_NV_copy_image o GLX_ARB_create_context o GLX_EXT_import_context o GLX_EXT_fbconfig_packed_float o GLX_EXT_framebuffer_sRGB o GLX_NV_present_video o GLX_NV_multisample_coverage o GLX_EXT_swap_control o GLX_NV_video_capture o GLX_ARB_create_context_profile For a description of these extensions, see the OpenGL extension registry at http://www.opengl.org/registry/ Some of the above extensions exist as part of core GLX 1.4 functionality, however, they are also exported as extensions for backwards compatibility. Unofficial GLX protocol support exists in NVIDIA's GLX client and GLX server implementations for the following OpenGL extensions: o GL_ARB_geometry_shader4 o GL_ARB_shader_objects o GL_ARB_texture_buffer_object o GL_ARB_vertex_buffer_object o GL_ARB_vertex_shader o GL_EXT_bindable_uniform o GL_EXT_compiled_vertex_array o GL_EXT_geometry_shader4 o GL_EXT_gpu_shader4 o GL_EXT_texture_buffer_object o GL_NV_geometry_program4 o GL_NV_vertex_program o GL_NV_parameter_buffer_object o GL_NV_vertex_program4 Until the GLX protocol for these OpenGL extensions is finalized, using these extensions through GLX indirect rendering will require the AllowUnofficialGLXProtocol X configuration option, and the __GL_ALLOW_UNOFFICIAL_PROTOCOL environment variable in the environment of the client application. Unofficial protocol requires the use of NVIDIA GLX libraries on both the client and the server. Note: GLX protocol is used when an OpenGL application indirect renders (i.e., runs on one computer, but submits protocol requests such that the rendering is performed on another computer). The above OpenGL extensions are fully supported when doing direct rendering. GLX visuals and FBConfigs are only available for X screens with depths 16, 24, or 30. ______________________________________________________________________________ Appendix E. Dots Per Inch ______________________________________________________________________________ DPI (Dots Per Inch), also known as PPI (Pixels Per Inch), is a property of an X screen that describes the physical size of pixels. Some X applications, such as xterm, can use the DPI of an X screen to determine how large (in pixels) to draw an object in order for that object to be displayed at the desired physical size on the display device. The DPI of an X screen is computed by dividing the size of the X screen in pixels by the size of the X screen in inches: DPI = SizeInPixels / SizeInInches Since the X screen stores its physical size in millimeters rather than inches (1 inch = 25.4 millimeters): DPI = (SizeInPixels * 25.4) / SizeInMillimeters The NVIDIA X driver reports the size of the X screen in pixels and in millimeters. On X.Org 6.9 or newer, when the XRandR extension resizes the X screen in pixels, the NVIDIA X driver computes a new size in millimeters for the X screen, to maintain a constant DPI (see the "Physical Size" column of the `xrandr -q` output as an example). This is done because a changing DPI can cause interaction problems for some applications. To disable this behavior, and instead keep the same millimeter size for the X screen (and therefore have a changing DPI), set the ConstantDPI option to FALSE (see Appendix B for details). You can query the DPI of your X screen by running: % xdpyinfo | grep -B1 dot which should generate output like this: dimensions: 1280x1024 pixels (382x302 millimeters) resolution: 85x86 dots per inch The NVIDIA X driver performs several steps during X screen initialization to determine the DPI of each X screen: o If the display device provides an EDID, and the EDID contains information about the physical size of the display device, that is used to compute the DPI, along with the size in pixels of the first mode to be used on the display device. If multiple display devices are used by this X screen, then the NVIDIA X screen will choose which display device to use. You can override this with the "UseEdidDpi" X configuration option: you can specify a particular display device to use; e.g.: Option "UseEdidDpi" "DFP-1" or disable EDID-computed DPI by setting this option to false: Option "UseEdidDpi" "FALSE" EDID-based DPI computation is enabled by default when an EDID is available. o If the "-dpi" commandline option to the X server is specified, that is used to set the DPI (see `X -h` for details). This will override the "UseEdidDpi" option. o If the "DPI" X configuration option is specified (see Appendix B for details), that will be used to set the DPI. This will override the "UseEdidDpi" option. o If none of the above are available, then the "DisplaySize" X config file Monitor section information will be used to determine the DPI, if provided; see the xorg.conf or XF86Config man pages for details. o If none of the above are available, the DPI defaults to 75x75. You can find how the NVIDIA X driver determined the DPI by looking in your X log file. There will be a line that looks something like the following: (--) NVIDIA(0): DPI set to (101, 101); computed from "UseEdidDpi" X config option Note that the physical size of the X screen, as reported through `xdpyinfo` is computed based on the DPI and the size of the X screen in pixels. The DPI of an X screen can be confusing when TwinView is enabled: with TwinView, multiple display devices (possibly with different DPIs) display portions of the same X screen, yet DPI can only be advertised from the X server to the X application with X screen granularity. Solutions for this include: o Use separate X screens, rather than TwinView; see Chapter 15 for details. o Experiment with different DPI settings to find a DPI that is suitable for both display devices. ______________________________________________________________________________ Appendix F. i2c Bus Support ______________________________________________________________________________ The NVIDIA Linux kernel module now includes i2c (also called I-squared-c, Inter-IC Communications, or IIC) functionality that allows the NVIDIA Linux kernel module to export i2c ports found on board NVIDIA cards to the Linux kernel. This allows i2c devices on-board the NVIDIA graphics card, as well as devices connected to the VGA and/or DVI ports, to be accessed from kernel modules or userspace programs in a manner consistent with other i2c ports exported by the Linux kernel through the i2c framework. You must have i2c support compiled into the kernel, or as a module, and X must be running. The i2c framework is available for both 2.4 and 2.6 series kernels. Linux kernel documentation covers the kernel and userspace /dev APIs, which you must use to access NVIDIA i2c ports. NVIDIA has noted that in some distibutions, i2c support is enabled. However, the Linux kernel module i2c-core.o (2.4) or i2c-core.ko (2.6), which provides the export infrastructure, was not shipped. In this case, you will need to build the i2c support module. For directions on how to build and install your kernel's i2c support, refer to your distribution's documentation for configuring, building, and installing the kernel and associated modules. For further information regarding the Linux kernel i2c framework, refer to the documentation for your kernel, located at .../Documentation/i2c/ within the kernel source tree. The following functionality is currently supported: I2C_FUNC_I2C I2C_FUNC_SMBUS_QUICK I2C_FUNC_SMBUS_BYTE I2C_FUNC_SMBUS_BYTE_DATA I2C_FUNC_SMBUS_WORD_DATA ______________________________________________________________________________ Appendix G. XvMC Support ______________________________________________________________________________ This release includes support for the XVideo Motion Compensation (XvMC) version 1.0 API on GeForce 6 series and GeForce 7 series add-in cards, as well as motherboard chipsets with integrated graphics that have PureVideo support based on these GPUs. There is a static library, "libXvMCNVIDIA.a", and a dynamic one, "libXvMCNVIDIA_dynamic.so", which is suitable for dlopening. XvMC's "IDCT" and "motion-compensation" levels of acceleration, AI44 and IA44 subpictures, and 4:2:0 Surfaces up to 2032x2032 are supported. libXvMCNVIDIA observes the XVMC_DEBUG environment variable and will provide some debug output to stderr when set to an appropriate integer value. '0' disables debug output. '1' enables debug output for failure conditions. '2' or higher enables output of warning messages. ______________________________________________________________________________ Appendix H. VDPAU Support ______________________________________________________________________________ This release includes support for the Video Decode and Presentation API for Unix-like systems (VDPAU) on most GeForce 8 series and newer add-in cards, as well as motherboard chipsets with integrated graphics that have PureVideo support based on these GPUs. VDPAU is only available for X screens with depths 16, 24, or 30. VDPAU supports Xinerama in a limited fashion. The following restrictions apply: o Physical X screen 0 must be driven by the NVIDIA driver. o Each application using VDPAU will only operate on a single physical X screen. If the VDPAU window is moved to a different physical X screen, the content of the window will be undefined. o VDPAU will only operate on physical X screens driven by the NVIDIA driver. Under Xinerama, each VDPAU application may operate on a different physical X screen. The environment variable VDPAU_NVIDIA_XINERAMA_PHYSICAL_SCREEN may be used to select which physical screen a VDPAU application will operate on. This variable should be set to the integer screen number as configured by the X configuration file. Physical X screen 0 is the default. The selected X screen must be driven by the NVIDIA driver. H1. IMPLEMENTATION LIMITS VDPAU is specified as a generic API - the choice of which features to support, and performance levels of those features, is left up to individual implementations. The details of NVIDIA's implementation are provided below. VDPVIDEOSURFACE The maximum supported resolution is 4096x4096. The following surface formats and get-/put-bits combinations are supported: o VDP_CHROMA_TYPE_420 (Supported get-/put-bits formats are VDP_YCBCR_FORMAT_NV12, VDP_YCBCR_FORMAT_YV12) o VDP_CHROMA_TYPE_422 (Supported get-/put-bits formats are VDP_YCBCR_FORMAT_UYVY, VDP_YCBCR_FORMAT_YUYV) VDPBITMAPSURFACE The maximum supported resolution is 16384x16384 pixels for the GeForce GTX 400 series and newer GPUs, and 8192x8192 pixels for older GPUs. The following surface formats are supported: o VDP_RGBA_FORMAT_B8G8R8A8 o VDP_RGBA_FORMAT_R8G8B8A8 o VDP_RGBA_FORMAT_B10G10R10A2 o VDP_RGBA_FORMAT_R10G10B10A2 o VDP_RGBA_FORMAT_A8 Note that VdpBitmapSurfaceCreate's frequently_accessed parameter directly controls whether the bitmap data will be placed into video RAM (VDP_TRUE) or system memory (VDP_FALSE). Note that if the bitmap data cannot be placed into video RAM when requested due to resource constraints, the implementation will automatically fall back to placing the data into system RAM. VDPOUTPUTSURFACE The maximum supported resolution is 16384x16384 pixels for the GeForce GTX 400 series and newer GPUs, and 8192x8192 pixels for older GPUs. The following surface formats are supported: o VDP_RGBA_FORMAT_B8G8R8A8 o VDP_RGBA_FORMAT_R10G10B10A2 For all surface formats, the following get-/put-bits indexed formats are supported: o VDP_INDEXED_FORMAT_A4I4 o VDP_INDEXED_FORMAT_I4A4 o VDP_INDEXED_FORMAT_A8I8 o VDP_INDEXED_FORMAT_I8A8 For all surface formats, the following get-/put-bits YCbCr formats are supported: o VDP_YCBCR_FORMAT_Y8U8V8A8 o VDP_YCBCR_FORMAT_V8U8Y8A8 VDPDECODER In all cases, VdpDecoder objects solely support 8-bit 4:2:0 streams, and only support writing to VDP_CHROMA_TYPE_420 surfaces. The exact set of supported VdpDecoderProfile values depends on the GPU in use. Appendix A lists which GPUs support which video feature set. An explanation of each video feature set may be found below. When reading these lists, please note that VC1_SIMPLE and VC1_MAIN may be referred to as WMV, WMV3, or WMV9 in other contexts. Partial acceleration means that VLD (bitstream) decoding is performed on the CPU, with the GPU performing IDCT and motion compensation. Complete acceleration means that the GPU performs all of VLD, IDCT, and motion compensation. VDPAU FEATURE SET A GPUs with VDPAU feature set A support at least the following VdpDecoderProfile values, and associated limits: o VDP_DECODER_PROFILE_MPEG1, VDP_DECODER_PROFILE_MPEG2_SIMPLE, VDP_DECODER_PROFILE_MPEG2_MAIN: o Partial acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 o VDP_DECODER_PROFILE_H264_MAIN, VDP_DECODER_PROFILE_H264_HIGH: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 o VDP_DECODER_PROFILE_VC1_SIMPLE, VDP_DECODER_PROFILE_VC1_MAIN, VDP_DECODER_PROFILE_VC1_ADVANCED: o Partial acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8190 VDPAU FEATURE SET B GPUs with VDPAU feature set B support at least the following VdpDecoderProfile values, and associated limits: o VDP_DECODER_PROFILE_MPEG1, VDP_DECODER_PROFILE_MPEG2_SIMPLE, VDP_DECODER_PROFILE_MPEG2_MAIN: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 o VDP_DECODER_PROFILE_H264_MAIN, VDP_DECODER_PROFILE_H264_HIGH: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width: 127 macroblocks (2032 pixels). o Maximum height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8190 o VDP_DECODER_PROFILE_VC1_SIMPLE, VDP_DECODER_PROFILE_VC1_MAIN, VDP_DECODER_PROFILE_VC1_ADVANCED: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8190 VDPAU FEATURE SET C GPUs with VDPAU feature set C support at least the following VdpDecoderProfile values, and associated limits: o VDP_DECODER_PROFILE_MPEG1, VDP_DECODER_PROFILE_MPEG2_SIMPLE, VDP_DECODER_PROFILE_MPEG2_MAIN: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 o VDP_DECODER_PROFILE_H264_MAIN, VDP_DECODER_PROFILE_H264_HIGH: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 o VDP_DECODER_PROFILE_VC1_SIMPLE, VDP_DECODER_PROFILE_VC1_MAIN, VDP_DECODER_PROFILE_VC1_ADVANCED: o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8190 o VDP_DECODER_PROFILE_MPEG4_PART2_SP, VDP_DECODER_PROFILE_MPEG4_PART2_ASP, VDP_DECODER_PROFILE_DIVX4_QMOBILE, VDP_DECODER_PROFILE_DIVX4_MOBILE, VDP_DECODER_PROFILE_DIVX4_HOME_THEATER, VDP_DECODER_PROFILE_DIVX4_HD_1080P, VDP_DECODER_PROFILE_DIVX5_QMOBILE, VDP_DECODER_PROFILE_DIVX5_MOBILE, VDP_DECODER_PROFILE_DIVX5_HOME_THEATER, VDP_DECODER_PROFILE_DIVX5_HD_1080P o Complete acceleration. o Minimum width or height: 3 macroblocks (48 pixels). o Maximum width or height: 128 macroblocks (2048 pixels). o Maximum macroblocks: 8192 The following features are currently not supported: o GMC (Global Motion Compensation) o Data partitioning o reversible VLC These GPUs also support VDP_VIDEO_MIXER_FEATURE_HIGH_QUALITY_SCALING_L1. VDPAU FEATURES NOTE 1 GPUs with this note may not support H.264 streams with the following widths: 49, 54, 59, 64, 113, 118, 123, 128 macroblocks (769-784, 849-864, 929-944, 1009-1024, 1793-1808, 1873-1888, 1953-1968, 2033-2048 pixels). VDPVIDEOMIXER The maximum supported resolution is 4096x4096. The video mixer supports all video and output surface resolutions and formats that the implementation supports. The video mixer supports at most 4 auxiliary layers. The following features are supported: o VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL o VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL_SPATIAL o VDP_VIDEO_MIXER_FEATURE_INVERSE_TELECINE o VDP_VIDEO_MIXER_FEATURE_NOISE_REDUCTION o VDP_VIDEO_MIXER_FEATURE_SHARPNESS o VDP_VIDEO_MIXER_FEATURE_LUMA_KEY In order for either VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL or VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL_SPATIAL to operate correctly, the application must supply at least 2 past and 1 future fields to each VdpMixerRender call. If those fields are not provided, the VdpMixer will fall back to bob de-interlacing. Both regular de-interlacing and half-rate de-interlacing are supported. Both have the same requirements in terms of the number of past/future fields required. Both modes should produce equivalent results. In order for VDP_VIDEO_MIXER_FEATURE_INVERSE_TELECINE to have any effect, one of VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL or VDP_VIDEO_MIXER_FEATURE_DEINTERLACE_TEMPORAL_SPATIAL must be requested and enabled. Inverse telecine has the same requirement on the minimum number of past/future fields that must be provided. Inverse telecine will not operate when "half-rate" de-interlacing is used. While it is possible to apply de-interlacing algorithms to progressive streams using the techniques outlined in the VDPAU documentation, NVIDIA does not recommend doing so. One is likely to introduce more artifacts due to the inverse telecine process than are removed by detection of bad edits etc. VDPPRESENTATIONQUEUE The resolution of VdpTime is approximately 10 nanoseconds. At some arbitrary point during system startup, the initial value of this clock is synchronized to the system's real-time clock, as represented by nanoseconds since since Jan 1, 1970. However, no attempt is made to keep the two time-bases synchronized after this point. Divergence can and will occur. NVIDIA's VdpPresentationQueue supports two mechanisms for displaying surfaces; overlay and blit-based. The overlay path will be used wherever possible, with the blit path acting as a more general fallback. At present, the selection of overlay v.s. blit path is made at the time of presentation queue creation. A VdpPresentationQueue allows a maximum of 8 surfaces to be QUEUED or VISIBLE at any one time. This limit is per presentation queue. If this limit is exceeded, VdpPresentationQueueDisplay currently blocks until an entry in the presentation queue becomes free. The following conditions or system configurations will prevent usage of the overlay path: o Overlay hardware already in use, e.g. by another VDPAU, GL, or X11 application, or by SDI output. o SLI or Multi-GPU enabled on the given X screen. o Desktop rotation enabled on the given screen. o X composite extension enabled on the given screen. Note that simply having the extension enabled is enough to prevent overlay usage; running an actual compositing manager is not required. o The environment variable VDPAU_NVIDIA_NO_OVERLAY is set to a string representation of a non-zero integer. o The driver determines that the performance requirements of overlay usage cannot be met by the current hardware configuration. Both the overlay and blit path sync to VBLANK. When TwinView is enabled, the blit path can only sync to one of the display devices; this may cause tearing corruption on the display device to which VDPAU is not syncing. You can use the environment variable VDPAU_NVIDIA_SYNC_DISPLAY_DEVICE to specify the display device to which VDPAU should sync. You should set this environment variable to the name of a display device; for example "CRT-1". Look for the line "Connected display device(s):" in your X log file for a list of the display devices present and their names. You may also find it useful to review Chapter 13 "Configuring Twinview" and the section on Ensuring Identical Mode Timings in Chapter 19. H2. PERFORMANCE LEVELS This documentation describes the capabilities of the NVIDIA VDPAU implementation. Hardware performance may vary significantly between cards. No guarantees are made, nor implied, that any particular combination of system configuration, GPU configuration, VDPAU feature set, VDPAU API usage, application, video stream, etc., will be able to decode streams at any particular frame rate. H3. GETTING THE BEST PERFORMANCE FROM THE API System performance (raw throughput, latency, and jitter tolerance) can be affected by a variety of factors. One of these factors is how the client application uses VDPAU; i.e. the number of surfaces allocated for buffering, order of operations, etc. NVIDIA GPUs typically contain a number of separate hardware modules that are capable of performing different parts of the video decode, post-processing, and display operations in parallel. To obtain the best performance, the client application must attempt to keep all these modules busy with work at all times. Consider the decoding process. At a bare minimum, the application must allocate one video surface for each reference frame that the stream can use (2 for MPEG or VC-1, a variable stream-dependent number for H.264) plus one surface for the picture currently being decoded. However, if this minimum number of surfaces is used, performance may be poor. This is because back-to-back decodes of non-reference frames will need to be written into the same video surface. This will require that decode of the second frame wait until decode of the first has completed; a pipeline stall. Further, if the video surfaces are being read by the video mixer for post-processing, and eventual display, this will "lock" the surfaces for even longer, since the video mixer needs to read the data from the surface, which prevents any subsequent decode operations from writing to the surface. Recall that when advanced de-interlacing techniques are used, a history of video surfaces must be provided to the video mixer, thus necessitating that even more video surfaces be allocated. For this reason, NVIDIA recommends the following number of video surfaces be allocated: o (num_ref + 3) for progressive content, and no de-interlacing. o (num_ref + 5) for interlaced content using advanced de-interlacing. Next, consider the display path via the presentation queue. This portion of the pipeline requires at least 2 output surfaces; one that is being actively displayed by the presentation queue, and one being rendered to for subsequent display. As before, using this minimum number of surfaces may not be optimal. For some video streams, the hardware may only achieve real-time decoding on average, not for each individual frame. Using compositing APIs to render on-screen displays, graphical user interfaces, etc., may introduce extra jitter and latency into the pipeline. Similarly, system level issues such as scheduler algorithms and system load may prevent the CPU portion of the driver from operating for short periods of time. All of these potential issues may be solved by allocating more output surfaces, and queuing more than one outstanding output surface into the presentation queue. The reason for using more than the minimum number of video surfaces is to ensure that the decoding and post-processing pipeline is not stalled, and hence is kept busy for the maximum amount of time possible. In contrast, the reason for using more than the minimum number of output surfaces is to hide jitter and latency in various GPU and CPU operations. The choice of exactly how many surfaces to allocate is a resource usage v.s. performance trade-off; Allocating more than the minimum number of surfaces will increase performance, but use proportionally more video RAM. This may cause allocations to fail. This could be particularly problematic on systems with a small amount of video RAM. A stellar application would automatically adjust to this by initially allocating the bare minimum number of surfaces (failures being fatal), then attempting to allocate more and more surfaces, provided the allocations kept succeeding, up to the suggested limits above. The video decoder's memory usage is also proportional to the maximum number of reference frames specified at creation time. Requesting a larger number of reference frames can significantly increase memory usage. Hence it is best for applications that decode H.264 to request only the actual number of reference frames specified in the stream, rather than e.g. hard-coding a limit of 16, or even the maximum number of surfaces allowable by some specific H.264 level at the stream's resolution. Note that the NVIDIA implementation correctly implements all required interlocks between the various pipelined hardware modules. Applications never need worry about correctness (providing their API usage is legal and sensible), but simply have to worry about performance. H4. ADDITIONAL NOTES Note that output and bitmap surfaces are not cleared to any specific value upon allocation. It is the application's responsibility to initialize all surfaces prior to using them as input to any function. Video surfaces are cleared to black upon allocation. H5. DEBUGGING AND TRACING The VDPAU wrapper library supports tracing VDPAU function calls, and their parameters. This tracing is controlled by the following environment variables: VDPAU_TRACE Enables tracing. Set to 1 to trace function calls. Set to 2 to trace all arguments passed to the function. VDPAU_TRACE_FILE Filename to write traces to. By default, traces are sent to stderr. This variable may either contain a plain filename, or a reference to an existing open file-descriptor in the format "&N" where N is the file descriptor number. The VDPAU wrapper library is responsible for determining which vendor-specific driver to load for a given X11 display/screen. At present, it hard-codes "nvidia" as the driver. The environment variable VDPAU_DRIVER may be set to override this default. The actual library loaded will be libvdpau_${VDPAU_DRIVER}.so. Setting VDPAU_DRIVER to "trace" is not advised. The NVIDIA VDPAU driver can emit some diagnostic information when an error occurs. To enable this, set the environment variable VDPAU_NVIDIA_DEBUG. A value of 1 will request a small diagnostic that will enable NVIDIA engineers to locate the source of the problem. A value of 3 will request that a complete stack backtrace be printed, which provide NVIDIA engineers with more detailed information, which may be needed to diagnose some problems. H6. MULTI-THREADING VDPAU supports multiple threads actively executing within the driver, subject to certain limitations. If any object is being created or destroyed, the VDPAU driver will become single-threaded. This includes object destruction during preemption cleanup. Otherwise, up to one thread may actively execute VdpDecoderRender per VdpDecoder object, and up to one thread may actively execute any other rendering API per VdpDevice (or child) object. Note that the driver enforces these restrictions internally; applications are not required to implement the rules outlined above. Finally, some of the "query" or "get" APIs may actively execute irrespective of the number of rendering threads currently executing. ______________________________________________________________________________ Appendix I. Tips for New Linux Users ______________________________________________________________________________ This installation guide assumes that the user has at least a basic understanding of Linux techniques and terminology. In this section we provide tips that the new user may find helpful. While the these tips are meant to clarify and assist users in installing and configuring the NVIDIA Linux Driver, it is by no means a tutorial on the use or administration of the Linux operating system. Unlike many desktop operating systems, it is relatively easy to cause irreparable damage to your Linux system. If you are unfamiliar with the use of Linux, we strongly recommend that you seek a tutorial through your distributor before proceeding. I1. THE COMMAND PROMPT While newer releases of Linux bring new desktop interfaces to the user, much of the work in Linux takes place at the command prompt. If you are familiar with the Windows operating system, the Linux command prompt is analogous to the Windows command prompt, although the syntax and use varies somewhat. All of the commands in this section are performed at the command prompt. Some systems are configured to boot into console mode, in which case the user is presented with a prompt at login. Other systems are configured to start the X window system, in which case the user must open a terminal or console window in order to get a command prompt. This can usually be done by searching the desktop menus for a terminal or console program. While it is customizable, the basic prompt usually consists of a short string of information, one of the characters '#', '$', or '%', and a cursor (possibly flashing) that indicates where the user's input will be displayed. I2. NAVIGATING THE DIRECTORY STRUCTURE Linux has a hierarchical directory structure. From anywhere in the directory structure, the 'ls' command will list the contents of that directory. The 'file' command will print the type of files in a directory. For example, % file filename will print the type of the file 'filename'. Changing directories is done with the 'cd' command. % cd dirname will change the current directory to 'dirname'. From anywhere in the directory structure, the command 'pwd' will print the name of the current directory. There are two special directories, '.' and '..', which refer to the current directory and the next directory up the hierarchy, respectively. For any commands that require a file name or directory name as an argument, you may specify the absolute or the relative paths to those elements. An absolute path begins with the "/" character, referring to the top or root of the directory structure. A relative path begins with a directory in the current working directory. The relative path may begin with '.' or '..'. Elements of a path are separated with the "/" character. As an example, if the current directory is '/home/jesse' and the user wants to change to the '/usr/local' directory, he can use either of the following commands to do so: % cd /usr/local or % cd ../../usr/local I3. FILE PERMISSIONS AND OWNERSHIP All files and directories have permissions and ownership associated with them. This is useful for preventing non-administrative users from accidentally (or maliciously) corrupting the system. The permissions and ownership for a file or directory can be determined by passing the -l option to the 'ls' command. For example: % ls -l drwxr-xr-x 2 jesse users 4096 Feb 8 09:32 bin drwxrwxrwx 10 jesse users 4096 Feb 10 12:04 pub -rw-r--r-- 1 jesse users 45 Feb 4 03:55 testfile -rwx------ 1 jesse users 93 Feb 5 06:20 myprogram -rw-rw-rw- 1 jesse users 112 Feb 5 06:20 README % The first character column in the first output field states the file type, where 'd' is a directory and '-' is a regular file. The next nine columns specify the permissions (see paragraph below) of the element. The second field indicates the number of files associated with the element, the third field indicates the owner, the fourth field indicates the group that the file is associated with, the fifth field indicates the size of the element in bytes, the sixth, seventh and eighth fields indicate the time at which the file was last modified and the ninth field is the name of the element. As stated, the last nine columns in the first field indicate the permissions of the element. These columns are grouped into threes, the first grouping indicating the permissions for the owner of the element ('jesse' in this case), the second grouping indicating the permissions for the group associated with the element, and the third grouping indicating the permissions associated with the rest of the world. The 'r', 'w', and 'x' indicate read, write and execute permissions, respectively, for each of these associations. For example, user 'jesse' has read and write permissions for 'testfile', users in the group 'users' have read permission only, and the rest of the world also has read permissions only. However, for the file 'myprogram', user 'jesse' has read, write and execute permissions (suggesting that 'myprogram' is a program that can be executed), while the group 'users' and the rest of the world have no permissions (suggesting that the owner doesn't want anyone else to run his program). The permissions, ownership and group associated with an element can be changed with the commands 'chmod', 'chown' and 'chgrp', respectively. If a user with the appropriate permissions wanted to change the user/group ownership of 'README' from jesse/users to joe/admin, he would do the following: # chown joe README # chgrp admin README The syntax for chmod is slightly more complicated and has several variations. The most concise way of setting the permissions for a single element uses a triplet of numbers, one for each of user, group and world. The value for each number in the triplet corresponds to a combination of read, write and execute permissions. Execute only is represented as 1, write only is represented as 2, and read only is represented as 4. Combinations of these permissions are represented as sums of the individual permissions. Read and execute is represented as 5, where as read, write and execute is represented as 7. No permissions is represented as 0. Thus, to give the owner read, write and execute permissions, the group read and execute permissions and the world no permissions, a user would do as follows: % chmod 750 myprogram I4. THE SHELL The shell provides an interface between the user and the operating system. It is the job of the shell to interpret the input that the user gives at the command prompt and call upon the system to do something in response. There are several different shells available, each with somewhat different syntax and capabilities. The two most common flavors of shells used on Linux stem from the Bourne shell ('sh') and the C-shell ('csh') Different users have preferences and biases towards one shell or the other, and some certainly make it easier (or at least more intuitive) to do some things than others. You can determine your current shell by printing the value of the 'SHELL' environment variable from the command prompt with % echo $SHELL You can start a new shell simply by entering the name of the shell from the command prompt: % csh or % sh and you can run a program from within a specific shell by preceding the name of the executable with the name of the shell in which it will be run: % sh myprogram The user's default shell at login is determined by whoever set up his account. While there are many syntactic differences between shells, perhaps the one that is encountered most frequently is the way in which environment variables are set. I5. SETTING ENVIRONMENT VARIABLES Every session has associated with it environment variables, which consist of name/value pairs and control the way in which the shell and programs run from the shell behave. An example of an environment variable is the 'PATH' variable, which tells the shell which directories to search when trying to locate an executable file that the user has entered at the command line. If you are certain that a command exists, but the shell complains that it cannot be found when you try to execute it, there is likely a problem with the 'PATH' variable. Environment variables are set differently depending on the shell being used. For the Bourne shell ('sh'), it is done as: % export MYVARIABLE="avalue" for the C-shell, it is done as: % setenv MYVARIABLE "avalue" In both cases the quotation marks are only necessary if the value contains spaces. The 'echo' command can be used to examine the value of an environment variable: % echo $MYVARIABLE Commands to set environment variables can also include references to other environment variables (prepended with the "$" character), including themselves. In order to add the path '/usr/local/bin' to the beginning of the search path, and the current directory '.' to the end of the search path, a user would enter % export PATH=/usr/local/bin:$PATH:. in the Bourne shell, and % setenv PATH /usr/local/bin:${PATH}:. in C-shell. Note the curly braces are required to protect the variable name in C-shell. I6. EDITING TEXT FILES There are several text editors available for the Linux operating system. Some of these editors require the X window system, while others are designed to operate in a console or terminal. It is generally a good thing to be competent with a terminal-based text editor, as there are times when the files necessary for X to run are the ones that must be edited. Three popular editors are 'vi', 'pico' and 'emacs', each of which can be started from the command line, optionally supplying the name of a file to be edited. 'vi' is arguably the most ubiquitous as well as the least intuitive of the three. 'pico' is relatively straightforward for a new user, though not as often installed on systems. If you don't have 'pico', you may have a similar editor called 'nano'. 'emacs' is highly extensible and fairly widely available, but can be somewhat unwieldy in a non-X environment. The newer versions each come with online help, and offline help can be found in the manual and info pages for each (see the section on Linux Manual and Info pages). Many programs use the 'EDITOR' environment variable to determine which text editor to start when editing is required. I7. ROOT USER Upon installation, almost all distributions set up the default administrative user with the username 'root'. There are many things on the system that only 'root' (or a similarly privileged user) can do, one of which is installing the NVIDIA Linux Driver. WE MUST EMPHASIZE THAT ASSUMING THE IDENTITY OF 'root' IS INHERENTLY RISKY AND AS 'root' IT IS RELATIVELY EASY TO CORRUPT YOUR SYSTEM OR OTHERWISE RENDER IT UNUSABLE. There are three ways to become 'root'. You may log in as 'root' as you would any other user, you may use the switch user command ('su') at the command prompt, or, on some systems, use the 'sudo' utility, which allows users to run programs as 'root' while keeping a log of their actions. This last method is useful in case a user inadvertently causes damage to the system and cannot remember what he has done (or prefers not to admit what he has done). It is generally a good practice to remain 'root' only as long as is necessary to accomplish the task requiring 'root' privileges (another useful feature of the 'sudo' utility). I8. BOOTING TO A DIFFERENT RUNLEVEL Runlevels in Linux dictate which services are started and stopped automatically when the system boots or shuts down. The runlevels typically range from 0 to 6, with runlevel 5 typically starting the X window system as part of the services (runlevel 0 is actually a system halt, and 6 is a system reboot). It is good practice to install the NVIDIA Linux Driver while X is not running, and it is a good idea to prevent X from starting on reboot in case there are problems with the installation (otherwise you may find yourself with a broken system that automatically tries to start X, but then hangs during the startup, preventing you from doing the repairs necessary to fix X). Depending on your network setup, runlevels 1, 2 or 3 should be sufficient for installing the Driver. Level 3 typically includes networking services, so if utilities used by the system during installation depend on a remote filesystem, Levels 1 and 2 will be insufficient. If your system typically boots to a console with a command prompt, you should not need to change anything. If your system typically boots to the X window system with a graphical login and desktop, you must both exit X and change your default runlevel. On most distributions, the default runlevel is stored in the file '/etc/inittab', although you may have to consult the guide for your own distribution. The line that indicates the default runlevel appears as id:n:initdefault: or similar, where "n" indicates the number of the runlevel. '/etc/inittab' must be edited as root. Please read the sections on editing files and root user if you are unfamiliar with this concept. Also, it is recommended that you create a copy of the file prior to editing it, particularly if you are new to Linux text editors, in case you accidentally corrupt the file: # cp /etc/inittab /etc/inittab.original The line should be edited such that an appropriate runlevel is the default (1, 2, or 3 on most systems): id:3:initdefault: After saving the changes, exit X. After the Driver installation is complete, you may revert the default runlevel to its original state, either by editing the '/etc/inittab' again or by moving your backup copy back to its original name. Different distributions provide different ways to exit X. On many systems, the 'init' utility will change the current runlevel. This can be used to change to a runlevel in which X is not running. # init 3 There are other methods by which to exit X. Please consult your distribution. I9. LINUX MANUAL AND INFO PAGES System manual or info pages are usually installed during installation. These pages are typically up-to-date and generally contain a comprehensive listing of the use of programs and utilities on the system. Also, many programs include the --help option, which usually prints a list of common options for that program. To view the manual page for a command, enter % man commandname at the command prompt, where commandname refers to the command in which you are interested. Similarly, entering % info commandname will bring up the info page for the command. Depending on the application, one or the other may be more up-to-date. The interface for the info system is interactive and navigable. If you are unable to locate the man page for the command you are interested in, you may need to add additional elements to your 'MANPATH' environment variable. See the section on environment variables.